Engine Types

How Rotary (Wankel) Engines Work: Torque, Exhaust and Quirks

How a Wankel rotary works, why its torque curve and exhaust note differ from a piston engine's, why rotaries burn oil, and where they're used today.

On this page
  1. What a Wankel rotary engine is
  2. The main parts
  3. How one rotor completes the four-stroke cycle
  4. Displacement and compression ratio
  5. The rotary engine torque curve
  6. Rotary engine exhaust: heat, noise and the “brap”
  7. Strengths of the rotary
  8. Weaknesses and common failure points
  9. Rotary cars and where rotaries are used today
  10. Is a rotary engine better than a V6?

What a Wankel rotary engine is

A Wankel rotary engine is an internal combustion engine that uses a spinning, rounded-triangle rotor instead of pistons that move up and down. It is named after Felix Wankel, the German engineer who developed the concept. Working engines appeared in the late 1950s, NSU put it into production cars in the 1960s, and Mazda became the company most associated with it, through models such as the RX-7 and RX-8.

The rotary still uses the familiar four phases of intake, compression, power and exhaust. What is different is how and where those phases happen, and that changes almost everything about how the engine feels, sounds and wears. For how the rotary fits among other engine designs, see our overview of engine types.

Note that “rotary engine” is also used for an older and quite different aircraft engine whose cylinders spun around a fixed crankshaft. That design is covered in our article on radial and rotary aircraft engines.

The main parts

  • Rotor. A rounded triangle with three curved faces. Each face usually has a shallow recess that forms part of the combustion chamber.
  • Rotor housing. The housing’s inner surface has a specific oval-like shape with a slight waist, called an epitrochoid. The rotor’s three tips stay in contact with it at all times.
  • Side housings. Flat plates that close off each side of the rotor housing. In many Mazda engines, the intake ports are in these side plates.
  • Eccentric shaft. The rotary’s equivalent of a crankshaft. Each rotor rides on an offset lobe of this shaft, and the rotor’s motion turns the shaft.
  • Seals. Apex seals sit in the three rotor tips and seal against the housing. Side seals and corner seals seal the rotor faces against the side housings. Oil seals keep lubricating oil out of the combustion chambers.
  • Spark plugs. Mazda rotaries typically use two plugs per rotor, known as leading and trailing plugs, because the combustion chamber is long and thin.
  • Ports. Instead of valves, the rotor itself uncovers and covers holes in the housings as it turns. There are no camshafts, valves or valve springs.

How one rotor completes the four-stroke cycle

As the rotor turns, its three tips divide the housing into three separate spaces. Each space grows and shrinks as the rotor moves, which is exactly what a piston and cylinder do.

Follow one face of the rotor:

  1. Intake. The face passes the intake port and the space behind it grows, drawing in air and fuel (or just air, in direct-injection designs).
  2. Compression. The space shrinks as the face moves around the housing, squeezing the charge.
  3. Power. The spark plugs fire near the point of greatest compression. The burning gas pushes on the rotor face, driving the rotor around and turning the eccentric shaft.
  4. Exhaust. The face uncovers the exhaust port and the shrinking space pushes the burnt gas out.

All three faces are doing this at the same time, one step apart. While one face is on its power stroke, another is compressing and the third is taking in a fresh charge.

How many power strokes per revolution?

The rotor turns at one-third the speed of the eccentric shaft. For every full turn of the rotor, the eccentric shaft turns three times, and each of the rotor’s three faces completes one power stroke.

That works out to one power stroke per rotor for every turn of the eccentric shaft. A two-rotor engine, like most Mazda rotaries, therefore gets two power strokes per shaft revolution. That is the same firing frequency as a four-cylinder four-stroke piston engine, which fires twice per crankshaft revolution. The difference is that each rotary power stroke lasts longer, around 270 degrees of shaft rotation, so the pulses overlap and the engine feels very smooth.

Displacement and compression ratio

Rotary displacement is a source of endless argument. Mazda’s 13B engine is usually quoted as 1.3 litres, from two rotors with a chamber volume of about 654 cc each. That figure counts one face per rotor.

The catch is that each rotor actually works through all three faces over three turns of the eccentric shaft. Depending on how you choose to compare it with a four-stroke piston engine, which completes its cycle over two crankshaft turns, you can argue for a much larger “equivalent” displacement. For this reason, motorsport bodies have historically applied correction factors when classing rotary engines against piston engines.

Compression ratios in Mazda’s production rotaries have generally sat somewhere around 9:1 to 10:1, with turbocharged versions at the lower end. Because a rotary compression test needs to read each of the three rotor faces separately, mechanics use a rotary-specific tester rather than a standard piston-engine gauge.

The rotary engine torque curve

Rotaries are known for feeling soft at low revs and then pulling harder and harder as the revs rise. A typical naturally aspirated rotary has modest peak torque for its power output, reached fairly high in the rev range, and a torque curve that is relatively flat across the middle. Because power is torque multiplied by engine speed, a flat torque curve that extends to very high revs produces power that keeps climbing almost to the redline.

Several features of the design shape that curve:

  • High-revving nature. With no valves, valve springs or reciprocating pistons, there is no valve float or piston speed limit to worry about in the same way. Mazda’s RX-8 engine was designed to rev to around 9,000 rpm. More revs means more power without more torque.
  • Port timing. The ports are fixed holes, so their timing cannot be varied in the way modern variable valve timing works on piston engines. Port shapes and sizes tuned for strong high-rpm breathing tend to sacrifice some low-rpm torque. Mazda used extra intake ports and valves in the intake system that open at higher revs to broaden the curve.
  • Leakage at low speed. The seals are not perfect. At low engine speeds, there is more time for gas to leak past them, which costs torque.
  • Chamber shape. The long, thin moving combustion chamber loses a lot of heat to the housing walls and burns less completely than a compact piston-engine chamber, which hurts efficiency and low-speed torque.

Turbocharging changes the picture. The third-generation RX-7 used sequential twin turbochargers, partly to fill in the low-rpm torque that a high-revving rotary naturally lacks.

Rotary engine exhaust: heat, noise and the “brap”

A rotary’s exhaust behaves differently from a piston engine’s, and that explains both its distinctive sound and some of its engineering headaches.

  • Sharp, hot pulses. The exhaust port is uncovered abruptly by the passing rotor tip, often while the gas is still at high pressure and, in some cases, still burning. Exhaust gas temperatures are high, so rotary exhaust systems need careful heat management.
  • A high-pitched, raspy note. The rapid, sharp exhaust pulses give rotaries a buzzy, high-pitched sound that is quite unlike a piston four-cylinder, even at the same firing frequency.
  • The “brap” idle. Heavily modified rotaries with enlarged (“bridge” or “peripheral”) intake ports have a lot of overlap between the intake and exhaust openings. At idle this makes combustion uneven, producing the choppy “brap-brap-brap” sound enthusiasts love. A stock rotary idles much more smoothly.
  • Unburned fuel. Because combustion in the long chamber is less complete, rotary exhaust tends to carry more unburned hydrocarbons. Early emissions-era Mazda rotaries used a thermal reactor, a hot chamber in the exhaust manifold where leftover fuel could burn off. Later engines used catalytic converters. In modified cars, unburned fuel igniting in the exhaust can produce pops and flames.

Why rotary engines smoke

A healthy rotary burns a small amount of oil by design. An oil metering pump feeds oil into the intake or housing so that it can lubricate the apex and side seals, which have no oil film of their own. That oil is burned along with the fuel. This is why rotary owners are often advised to check the oil level frequently and top it up between changes.

Some smoke can therefore be normal, especially at start-up. Heavier or persistent smoke usually points to a problem:

  • Blue-grey smoke that persists can indicate worn oil seals, worn internal seals or, on turbocharged engines, a failing turbo seal.
  • White smoke with a sweet smell can indicate coolant entering the combustion chambers, often from failed coolant seals between the housings.
  • Black smoke generally means the engine is running too rich, which can happen if it has flooded.

Smoke has many possible causes, so a mechanic experienced with rotaries is the best person to diagnose it.

Mufflers, resonators and rotary exhaust systems

Every car exhaust carries burnt gas away from the engine and the cabin, cleans it with a catalytic converter, and reduces noise.

  • A muffler reduces overall noise, using internal chambers, perforated tubes or sound-absorbing packing.
  • A resonator is tuned to cancel particular frequencies, such as an annoying drone at highway speed.

Because a rotary’s exhaust note is so high-pitched and raspy, rotary exhaust systems often use both. Owners who fit louder aftermarket systems should check local noise and emissions rules.

Strengths of the rotary

  • Compact and light for its power output
  • Very few moving parts: in a two-rotor engine, essentially the two rotors and the eccentric shaft
  • Smooth: only rotating parts, with overlapping power pulses
  • High-revving, with no valvetrain to limit engine speed
  • Simple to scale by adding rotors; Mazda’s four-rotor 787B won the 24 Hours of Le Mans in 1991

Weaknesses and common failure points

  • Fuel economy. The long combustion chamber loses heat and burns less completely, so rotaries generally use more fuel than piston engines of similar output.
  • Oil consumption. By design, as described above.
  • Emissions. Higher hydrocarbon emissions made it increasingly hard to meet regulations, one reason Mazda ended RX-8 production in 2012.
  • Apex seal wear. Worn or broken apex seals cause low compression, which often shows up as hard starting, especially when hot, and lost power. Rebuilds are a known part of long-term rotary ownership.
  • Flooding. Some rotaries, the RX-8 in particular, have a reputation for flooding if started and switched off again before warming up.
  • Coolant seals. Failed seals between housings can let coolant into the chambers or combustion gas into the cooling system.
  • Specialist knowledge. Fewer mechanics are familiar with rotaries than with piston engines.

Rotary cars and where rotaries are used today

Well-known rotary road cars include the NSU Spider and Ro80, the Mazda Cosmo, RX-2, RX-3, RX-7 and RX-8. Mercedes-Benz and others built rotary prototypes, such as the C111, but did not put them into series production.

Today the rotary survives mainly where its compact size and smoothness matter more than its efficiency. Mazda’s MX-30 R-EV uses a small single-rotor engine purely as a generator to charge the battery, and Mazda has shown rotary range-extender concepts. Small rotaries are also used in some drones, light aircraft and portable power units.

The rotary’s high revs and simplicity have long made it interesting for racing. For why it never appeared in Formula One, see why F1 cars don’t use rotary engines.

Is a rotary engine better than a V6?

It depends on what you value. A rotary is smaller, lighter and smoother than a V6 of similar power, and it revs much higher. A V6 typically offers better fuel economy, more low-rpm torque, lower oil consumption, longer intervals between major work, and far wider parts and service support. For most daily driving, a modern piston engine is the more practical choice. The rotary appeals to drivers who value its character and are willing to accept the extra care it needs. If you are comparing mainstream piston engines instead, our comparison of four-cylinder and V6 engines may help.

The complete guide to engine types

Types of Car Engines: Layouts, Cylinder Arrangements and Placement
Read the guide

Keep exploring

Guides from other topics

All topics →