Engine Types

How Gas Turbine Engines Work: Turbojets, Turboshafts and Their Parts

How gas turbine engines work: what the inlet, compressor, combustor, turbine and nozzle do, and how turbojets, turbofans, turboprops and turboshafts differ.

On this page
  1. The basic idea
  2. Gas turbine parts and their functions
  3. How a turbojet engine works
  4. Turbofans: the modern airliner engine
  5. Turboprops
  6. How a turboshaft engine works
  7. Comparing the main types
  8. Strengths and disadvantages of gas turbines
  9. Why cars don’t use gas turbines
  10. Gas turbine questions

The basic idea

A gas turbine is an engine that burns fuel continuously in a stream of compressed air and uses the hot, expanding gas to spin a turbine. A piston engine does its intake, compression, power and exhaust in turns inside the same cylinder. A gas turbine does all four at the same time, in different parts of the engine, with air flowing steadily from front to back.

The process is sometimes summed up as “suck, squeeze, bang, blow”:

  1. Suck. Air is drawn in through the inlet.
  2. Squeeze. A compressor raises its pressure.
  3. Bang. Fuel is burned in the compressed air, heating it.
  4. Blow. The hot gas expands through a turbine, which drives the compressor, and then leaves the engine either as a fast jet or after driving another turbine connected to a shaft.

The thermodynamic cycle behind this is called the Brayton cycle. Gas turbines power jet aircraft, helicopters, many warships, some tanks, pipeline compressors and a large share of the world’s electricity generation. For how they relate to other engine types, see our overview of engine types.

Gas turbine parts and their functions

Inlet

The inlet guides air smoothly into the compressor with as little loss as possible. On an airliner it is the round opening at the front of the engine. On supersonic aircraft, the inlet also has to slow the incoming air below the speed of sound before it reaches the compressor, which is why fighter inlets often have ramps or cones.

Compressor

The compressor raises the pressure of the incoming air. There are two main types:

  • Axial compressors use many rows of small blades on spinning discs, with rows of fixed vanes (stators) between them. Each stage adds a little pressure. Large jet engines use axial compressors because they handle large airflows efficiently.
  • Centrifugal compressors use a single spinning impeller that flings air outward. They are robust and compact and are common in smaller engines, including many helicopter engines and auxiliary power units. Some engines combine axial stages followed by a centrifugal stage.

Modern large engines reach very high overall pressure ratios, compressing air to several dozen times atmospheric pressure. The higher the pressure ratio, generally the more efficient the engine, within the limits of materials and temperature.

Combustor

In the combustor, also called the combustion chamber or burner, fuel is sprayed into the high-pressure air and burned continuously. Igniters are only needed to start the engine; after that, the flame sustains itself. Combustors come in can, can-annular and annular designs, with annular combustors, a single ring-shaped chamber, common in modern engines.

Only part of the air is used for burning. The rest is mixed in afterward to cool the gas and protect the turbine downstream.

Turbine

The turbine extracts energy from the hot gas. It consists of rows of blades on discs, with fixed nozzle guide vanes in front that direct the gas onto the blades at the right angle. The first turbine stage connects through a shaft to the compressor and keeps it turning, which is what makes the engine self-sustaining.

Turbine blades operate in extremely hot gas. In modern engines the gas entering the turbine can be hotter than the melting point of the metal the blades are made of. They survive because they are made from nickel-based superalloys, often cast as single crystals, have internal cooling passages fed with compressor air, and are protected by thermal barrier coatings.

Exhaust nozzle

After the turbine, the remaining gas leaves through the exhaust. In a jet engine, the nozzle is shaped to accelerate the gas into a high-speed jet that produces thrust. In engines that drive a shaft, the exhaust is designed mainly to carry the gas away with little loss.

Shafts, spools and bearings

A compressor and the turbine that drives it, joined by a shaft, are called a spool. Many engines have two or three spools running at different speeds, one inside another. For example, a low-pressure turbine at the back may drive the fan at the front through a long inner shaft, while a high-pressure turbine drives the high-pressure compressor through a shorter outer shaft. Different speeds let each section run closer to its best efficiency. The shafts run on high-speed bearings supplied by the engine’s oil system.

Accessory gearbox and fuel control

An accessory gearbox, driven from one of the engine shafts, runs pumps for fuel, oil and hydraulics and the electrical generators. It is also where the starter connects.

The fuel control system meters fuel to the combustor, matching it to the power the pilot or operator asks for while keeping temperatures, speeds and pressures within safe limits. Older and many smaller engines use a hydromechanical fuel control unit (FCU). Most modern engines use FADEC, full authority digital engine control, in which computers manage fuel flow and other engine settings.

How a turbojet engine works

A turbojet is the simplest jet engine. All of the air that enters passes through the compressor, combustor and turbine. The turbine takes only as much energy as it needs to drive the compressor and accessories. The rest of the energy stays in the gas, which leaves the nozzle at very high speed.

Thrust comes from Newton’s third law. The engine accelerates a mass of air backward, and the reaction pushes the engine and the aircraft forward. A turbojet accelerates a relatively small mass of air to a very high speed.

Some military turbojets and turbofans add an afterburner: extra fuel is sprayed into the hot exhaust behind the turbine and burned, greatly increasing thrust at the cost of very high fuel consumption.

Turbojets are efficient at high speeds but noisy and thirsty at the speeds airliners fly, so they have largely been replaced by turbofans except in some specialised uses and small engines.

Turbofans: the modern airliner engine

A turbofan adds a large fan at the front, driven by a low-pressure turbine. Only some of the air the fan moves goes through the core of the engine. The rest flows around the core in a bypass duct and is pushed out the back. The ratio of bypass air to core air is called the bypass ratio, and large modern airliner engines have high bypass ratios.

Moving a large mass of air at a moderate speed is more efficient and quieter than moving a small mass at a very high speed. Most of the thrust from a modern airliner engine comes from the fan rather than the hot core exhaust.

Turboprops

A turboprop uses a gas turbine to turn a propeller through a reduction gearbox. Most of the energy in the gas is taken out by the turbines to drive the propeller, with only a small amount of thrust from the exhaust. Turboprops are efficient at lower speeds and altitudes, which is why they are common on regional airliners and military transports such as the C-130 Hercules.

How a turboshaft engine works

A turboshaft is built to produce power at a rotating output shaft rather than thrust. It has the same core as other gas turbines: inlet, compressor, combustor and a turbine driving the compressor. That core is often called the gas generator.

Behind the gas generator sits a second turbine, the power turbine. In most turboshafts this is a free power turbine: it is not mechanically connected to the gas generator, only to the output shaft. The hot gas leaving the gas generator spins it, and it drives the output shaft, usually through a reduction gearbox that brings the very high turbine speed down to something the load can use.

The free turbine design lets the gas generator and the output run at different speeds. In a helicopter, for example, the main rotor needs to turn at a nearly constant speed while the engine’s power output changes, and the free turbine makes that much easier.

Turboshafts are designed to extract as much energy from the gas as possible, leaving little for jet thrust. They power:

  • Helicopters
  • The M1 Abrams tank, whose AGT1500 engine is a gas turbine
  • Many naval ships, often as marine versions of aircraft engines
  • Generators and pipeline compressors
  • Auxiliary power units (APUs) in airliners

Industrial and power-station gas turbines work on the same principle at a much larger scale.

Comparing the main types

Type Where the useful output goes Typical use
Turbojet High-speed exhaust jet Early jets, missiles, some small engines
Turbofan Fan bypass air plus core jet Airliners, most modern military jets
Turboprop Propeller via reduction gearbox Regional airliners, transports, utility aircraft
Turboshaft Output shaft via power turbine Helicopters, ships, tanks, generators, APUs

Ramjets and scramjets are related air-breathing engines that skip the compressor and turbine entirely. They rely on very high flight speed to compress the incoming air, so they cannot work from a standstill.

Strengths and disadvantages of gas turbines

Strengths:

  • Very high power for their weight and size
  • Smooth running, with no reciprocating parts
  • Long periods of continuous operation at steady power, which suits aircraft and power plants
  • Able to burn a range of fuels, in many designs

Disadvantages:

  • Poor efficiency at low power. Gas turbines are most efficient near their design power. At idle or part load, fuel consumption is high relative to the power produced.
  • Slow throttle response. The spinning spools take time to speed up, a delay known as spool-up time.
  • Cost. High-temperature alloys, precision manufacturing and strict quality requirements make them expensive to build and overhaul.
  • Sensitivity to foreign objects. Debris, birds or ice drawn into the inlet can damage blades.
  • Noise and heat. Large amounts of hot exhaust and high-frequency noise must be managed.

Why cars don’t use gas turbines

Carmakers experimented seriously with turbine cars. The best-known example is Chrysler’s Turbine Car of the early 1960s, of which a small number were lent to members of the public to drive. The problems were the ones listed above: high fuel use at idle and in stop-start traffic, slow throttle response, very hot exhaust, high manufacturing cost and difficulty meeting emerging emissions limits for nitrogen oxides. Piston engines, which are efficient across a wider range of loads, remained the better fit for road vehicles.

Gas turbine questions

Is a turboshaft engine a jet engine?

A turboshaft is a gas turbine, the same family of engines that includes jet engines, and it shares the same core of compressor, combustor and turbine. But it is not usually called a jet engine, because it does not produce its useful output as a jet. Its job is to drive a shaft, and most of the energy in the gas is used for that rather than for thrust.

Can a gas turbine run on diesel?

Many can. Industrial and marine gas turbines often burn diesel or similar distillate fuels, and many also run on natural gas. Aviation kerosene (jet fuel) is itself a close relative of diesel. The M1 Abrams tank’s turbine is designed to run on several fuels. However, each engine is designed and, in aviation, certified for specific fuels, so a given engine should only be run on fuels its manufacturer approves.

Why do pilots reduce thrust after takeoff?

Takeoff thrust works the engine very hard, with high temperatures in the turbine section. Engines are typically rated to use maximum takeoff thrust only for a limited time, often a few minutes. Reducing to climb thrust once the aircraft is safely airborne limits wear and heat stress on the engine, reduces fuel burn and lowers noise over the surrounding area. Many airlines also use reduced takeoff thrust when the runway length and conditions allow, for similar reasons.

What is the most powerful engine on a plane?

The most powerful aircraft engines by thrust are the large turbofans on long-haul twin-engine airliners. General Electric’s GE90 and its successor, the GE9X, built for versions of the Boeing 777, are generally cited as the most powerful, with the GE9X recognised by Guinness World Records for the highest thrust recorded by a jet engine during testing.

How much does a jet engine cost?

Prices vary enormously by size and type. Small turbojets for model aircraft and hobby use can cost a few thousand dollars. Engines for business jets and helicopters are far more expensive, and large airliner turbofans are widely reported to cost tens of millions of dollars each. Manufacturers rarely publish exact prices, and much of an engine’s lifetime cost comes from maintenance and overhauls rather than the purchase price.

For a look back at the piston engines that gas turbines replaced in most aircraft, see our article on radial and rotary aircraft engines.

The complete guide to engine types

Types of Car Engines: Layouts, Cylinder Arrangements and Placement
Read the guide

Keep exploring

Guides from other topics

All topics →