What valve overlap is
Valve overlap is the period, measured in degrees of crankshaft rotation, when the intake valve and the exhaust valve of the same cylinder are open at the same time. It happens around top dead center (TDC) at the changeover from the exhaust stroke to the intake stroke: the exhaust valve hasn’t quite closed yet, and the intake valve has already started to open.
If you picture the valves as simple doors that open exactly at the start of a stroke and close exactly at the end, overlap seems strange. Real engines don’t work that way, because air and exhaust gas have mass and take time to start and stop moving.
Why engines open both valves at once
Scavenging and gas momentum
During the exhaust stroke, burned gas rushes out through the exhaust valve and into the exhaust port and header. That moving column of gas has momentum. As the piston approaches TDC, the departing exhaust can create a low-pressure region behind it in the cylinder.
If the intake valve opens a little early, that low pressure helps draw fresh mixture into the cylinder before the piston has even started down. The incoming charge can also help push the last of the exhaust gas out. This is called scavenging. At the right engine speed, with a well-tuned intake and exhaust, it fills the cylinder more completely and makes more power.
Holding the exhaust valve open a little past TDC gives the exhaust more time to leave, and opening the intake valve before TDC means it’s already well open when the piston starts pulling the charge in. Overlap is the result of both.
The catch is that this only works well over a certain RPM range. At low speed, gas moves slowly and the timing of the pressure waves in the intake and exhaust no longer helps. That’s where reversion comes in, covered below.
How overlap is measured and calculated
From cam-card opening and closing points
A camshaft’s specification card (cam card) lists when each valve opens and closes, usually relative to TDC and BDC. The overlap is simply:
Overlap = intake opening (degrees BTDC) + exhaust closing (degrees ATDC)
For example, if the intake opens at 20° BTDC and the exhaust closes at 18° ATDC, the overlap is 20 + 18 = 38 crankshaft degrees.
From duration and lobe separation angle
If you only know the durations and the lobe separation angle (LSA), the angle between the intake and exhaust lobe centerlines, you can use:
Overlap = (intake duration + exhaust duration) ÷ 2 − (2 × LSA)
Durations are in crankshaft degrees and LSA is normally quoted in camshaft degrees, which is why it’s doubled.
Worked example: a cam with 260° intake duration, 270° exhaust duration and a 110° LSA gives (260 + 270) ÷ 2 − 220 = 265 − 220 = 45° of overlap. Tightening the LSA to 106° on the same durations raises overlap to 53°; widening it to 114° drops it to 37°.
This formula gives the same answer as the opening-plus-closing method when the cam card and installed centerlines match, so it’s a useful cross-check.
Advertised vs 0.050-inch overlap
Valve events depend on where you start measuring. Cam cards often quote two sets of figures:
- Advertised duration, measured from a small lift figure that varies by manufacturer
- Duration at 0.050 inch of lift, a more consistent standard used for comparing cams
Overlap calculated from 0.050-inch figures is much smaller than advertised overlap, and on mild cams it can even come out negative, meaning neither valve is open past 0.050 inch at the same time. When comparing cams, compare overlap figures measured the same way.
What more or less overlap does
As a general rule:
| More overlap | Less overlap |
|---|---|
| Better cylinder filling at high RPM | Better low-speed torque and response |
| Lumpy, uneven idle (“cammy” sound) | Smooth idle |
| Lower manifold vacuum at idle | Higher manifold vacuum |
| More unburned fuel at idle and low speed | Cleaner low-speed running |
| Suits racing and high-RPM engines | Suits road engines, towing, efficiency |
Low idle vacuum matters on road vehicles because some systems, such as traditional vacuum brake boosters, depend on it. That’s one reason engine builders consider overlap carefully when choosing an aftermarket camshaft.
Overlap also lets some exhaust gas stay in the cylinder or be drawn back in, acting as a form of internal exhaust gas recirculation. Modern engines use this deliberately at light load to reduce pumping losses and nitrogen oxide formation.
What reversion is
Reversion is gas flowing the wrong way through the engine: back from the cylinder into the intake, or back from the exhaust into the cylinder. It’s closely tied to overlap and valve timing.
Exhaust reversion during overlap
At low RPM with a lot of overlap, pressure in the cylinder and exhaust port at the end of the exhaust stroke can be higher than pressure in the intake manifold, especially at idle, when the throttle is nearly closed and manifold pressure is low. When the intake valve opens, exhaust gas can push back into the intake port and manifold instead of the fresh charge flowing in. Pressure waves bouncing back through the exhaust system can make this worse.
That exhaust dilutes the next intake charge, which is a big part of why high-overlap engines idle roughly.
Intake reversion after bottom dead center
The intake valve normally closes some way after bottom dead center (BDC), so the moving charge can keep filling the cylinder while the piston starts back up. At high RPM, the charge’s momentum carries it in. At low RPM it doesn’t have that momentum, and the rising piston can push some of the fresh mixture back out into the intake before the valve closes.
On carbureted engines this can show as a fuel mist hovering above the carburetor at low speed, sometimes called “standoff”. It also reduces low-speed torque, because less mixture stays trapped in the cylinder.
Signs of reversion
Typical signs include:
- Rough, uneven idle
- Poor throttle response and torque at low RPM
- Fuel standoff above the carburetor or throttle body
- Soot or exhaust residue inside the intake on heavily cammed engines
- Low and fluctuating idle vacuum
These symptoms can also come from vacuum leaks, ignition faults or incorrect valve timing, so they’re not proof of reversion on their own.
How engine builders reduce it
Approaches include choosing a cam with less overlap or a later intake opening, widening the lobe separation angle, raising idle speed, and designing the exhaust and intake so their pressure waves help rather than hurt at the speeds that matter. Some exhaust headers use “anti-reversion” features, such as a step at the port or a cone inside the primary tube, intended to make backward flow harder than forward flow. How much these help depends on the engine.
How variable valve timing manages overlap
Fixed cams force a single compromise. Variable valve timing lets the engine change overlap as it runs. With separate phasers on the intake and exhaust camshafts, the engine computer can reduce overlap at idle for smoothness and stable combustion, add some at part load for internal EGR and lower pumping losses, and set it for best breathing at high RPM. Some turbocharged direct-injection engines use overlap at low RPM, when intake pressure is higher than exhaust pressure, to blow residual exhaust out and help the turbo spool.
For more on how these systems work, see variable valve timing, CVVD and camless engines. And if a belt or chain has moved and the valve events are no longer where they should be, overlap is one of many things that changes; see what happens if valve timing is incorrect.
Does valve clearance affect overlap?
Yes. On engines with adjustable valve lash (clearance), the clearance has to be taken up before the cam lobe can start moving the valve.
- Too much clearance makes the valve open later and close earlier than designed, reducing effective duration, lift and overlap. It’s usually noisy (ticking) and can reduce power.
- Too little clearance makes the valve open earlier and close later. In the worst case the valve doesn’t fully close, so it loses compression and can’t transfer heat into the cylinder head, which can burn the valve, especially exhaust valves.
That’s why valve lash should be set to the manufacturer’s specification, measured at the temperature the specification calls for. Engines with hydraulic lifters adjust their clearance automatically.
Reversion vs a “reverse-flow” engine
The terms sound similar but mean different things. Reversion is backward gas flow during operation. A reverse-flow cylinder head is simply a layout in which the intake and exhaust ports are on the same side of the head, unlike a crossflow head, which has them on opposite sides. Reverse-flow heads were common on many older inline engines; crossflow heads became more common later, partly because they allow straighter ports. Neither layout means the engine suffers from reversion.
For the wider context on how valve events fit alongside ignition timing, see our engine timing guide.