What a crankshaft does
The crankshaft turns the up-and-down motion of the pistons into rotation. Each piston is joined to the crank by a connecting rod. The rod’s lower end wraps around an offset pin on the crankshaft. When combustion pushes the piston down, the rod pushes that offset pin around in a circle, and the whole shaft turns. It works like your feet on bicycle pedals.
That rotation is what the engine produces. At the back, the crankshaft drives the flywheel or flexplate and from there the transmission. At the front, it drives the timing belt or chain (which turns the camshafts) and the accessory belt (alternator, water pump on many engines, A/C compressor). It also keeps the pistons moving through the non-power strokes, carried by its own momentum and that of the flywheel.
For where the crankshaft sits among the other major components, see our labeled guide to engine parts and functions.
Parts of a crankshaft
A crankshaft looks like one solid forging or casting, but each section has its own job.
| Part | What it is | What it does |
|---|---|---|
| Main journals | Polished round sections on the crank’s centerline | Ride in the main bearings; the crank spins on these |
| Rod journals (crankpins) | Polished sections offset from the centerline | Connecting rods attach here; their offset creates the stroke |
| Crank webs (cheeks) | The arms joining main journals to rod journals | Carry the load between the journals |
| Counterweights | Heavy lobes opposite the crankpins | Offset the weight of the pins, rods and pistons to reduce vibration |
| Fillets | Small radiused corners where journals meet webs | Spread stress; a sharp corner here would crack easily |
| Oil passages | Drilled holes from main journals to rod journals | Carry pressurized oil to the rod bearings |
| Thrust surfaces | Machined faces at one main journal | Work with the thrust bearing to stop the crank moving fore and aft |
| Snout (nose) | The front end of the crank | Carries the timing sprocket or gear, harmonic balancer and pulley |
| Rear flange | The back end of the crank | Flywheel or flexplate bolts here; the rear main seal rides on it |
A few related parts are bolted or pressed onto the crankshaft rather than being part of it:
- Harmonic balancer (torsional damper). It sits on the snout and absorbs the twisting vibration each power pulse sends through the crank.
- Timing sprocket or gear. It drives the timing belt or chain.
- Reluctor (trigger) wheel. A toothed ring, on the crank or behind the balancer, that the crankshaft position sensor reads.
- Flywheel or flexplate. It adds rotating mass, carries the starter ring gear, and links the engine to the transmission.
The distance from the main journal’s center to the rod journal’s center is called the throw. The piston’s stroke, how far it travels from top to bottom, is twice the throw. That is why “stroker” cranks with longer throws increase engine displacement.
Cast, forged and billet crankshafts
Crankshafts are made in three main ways:
- Cast. Molten iron (often nodular or ductile iron) or steel is poured into a mold and then machined. Casting is economical and is used in many everyday engines. A cast crank is strong enough for normal loads.
- Forged. Hot steel is pressed into shape. Forging aligns the metal’s grain with the crank’s shape, which generally makes it tougher and more fatigue-resistant than a casting. Forged cranks are common in diesels, performance engines and turbocharged engines.
- Billet. The crank is machined from a solid steel bar. Billet cranks are expensive and used mostly in racing and custom builds, where designers want specific dimensions.
Many crankshafts are also surface-hardened, for example by induction hardening or nitriding, so the journals resist wear and the fillets resist fatigue.
Crank angle explained
Crank angle is the position of the crankshaft in degrees as it rotates. It is the reference engineers and mechanics use to describe when things happen inside an engine: when a valve opens, when the spark fires, when fuel is injected.
How many degrees in a four-stroke cycle?
A four-stroke engine needs two full crankshaft revolutions, or 720 degrees, to complete one cycle. Each stroke takes about 180 degrees:
| Stroke | Approximate crank angle |
|---|---|
| Intake | 0°–180° |
| Compression | 180°–360° |
| Power | 360°–540° |
| Exhaust | 540°–720° |
In practice the valves open and close a little before or after these points, so the strokes overlap slightly. A two-stroke engine completes its cycle in a single revolution, 360 degrees.
TDC, BDC and timing in degrees
Two positions anchor crank angle:
- TDC (top dead center). The piston is at the very top of its travel.
- BDC (bottom dead center). The piston is at the very bottom.
Events are then described relative to these points. Ignition timing is usually given in degrees BTDC (before top dead center). The spark fires a little before the piston reaches the top so the mixture has time to burn and build pressure just as the piston starts down. The ECU varies this angle with engine speed and load. Valve timing is described the same way, for example “intake opens X degrees BTDC, closes Y degrees ABDC (after bottom dead center).”
Firing intervals
In an evenly firing four-stroke engine, the 720 degrees of the cycle are shared equally between the cylinders. Divide 720 by the number of cylinders and you get the crank angle between power strokes:
| Cylinders | Firing interval (even-firing four-stroke) |
|---|---|
| 1 | 720° |
| 2 (even-firing) | 360° |
| 3 | 240° |
| 4 | 180° |
| 6 | 120° |
| 8 | 90° |
| 10 | 72° |
| 12 | 60° |
More cylinders means more frequent, overlapping power pulses, which is one reason larger cylinder counts feel smoother. Not every engine fires evenly. Some twins and some V6 and V10 designs have uneven intervals.
Crankpin layouts: cross-plane vs flat-plane
The angle between crankpins as you look down the crank’s axis defines the crank’s “plane.” It mostly comes up with V8s:
- Cross-plane V8. The four crankpins sit at 90° to each other, so from the end they form a cross. With heavy counterweights this gives very good balance. Firing alternates unevenly between the two banks, which produces the classic V8 burble. Most road-going V8s use this layout.
- Flat-plane V8. The crankpins sit at 0° and 180°, all in one plane, like two inline-fours sharing a crank. It is lighter, revs more freely and fires each bank evenly, which helps exhaust tuning. The trade-off is more secondary vibration. Flat-plane cranks are used mainly in high-revving sports and racing V8s.
Our article on what V6, V8 and V12 mean goes into how these layouts affect balance and sound.
What does a 270-degree crank mean?
A 270-degree crank is a parallel-twin crankshaft whose two crankpins are offset so the cylinders fire 270° apart, then 450° apart (270 + 450 = 720). The uneven rhythm makes the twin sound and feel much like a 90-degree V-twin. Riders often describe it as giving good traction feel. Several modern motorcycle twins from Yamaha, Triumph and Honda use this layout. The older alternatives were the 360-degree crank (both pistons rise together, even firing) and the 180-degree crank (pistons move opposite each other, uneven firing).
Crank angle vs bank angle
Don’t confuse crank angle with bank angle, the angle between the two cylinder banks of a V engine (such as 60° or 90°). The two are related, though. A 90° V8 with a cross-plane crank can fire evenly every 90° because the bank angle matches the firing interval. A 60° or 90° V6 needs a 120° interval for even firing, so many V6s use split (offset) crankpins to get there.
How the engine measures crank angle
Modern engines measure crank angle electronically. A crankshaft position sensor reads the teeth on the reluctor wheel as they pass. A deliberate gap (one or more missing teeth) marks a reference point. From that, the ECU knows the crank’s exact position and speed and can time spark and fuel injection.
The crank sensor alone can’t tell whether a piston at TDC is on compression or exhaust, because both happen at the same crank position, one revolution apart. So the ECU also reads a camshaft position sensor. Our engine sensors guide covers both sensors and what happens when they fail. A failed crank sensor is a common cause of stalling and no-start, but it is a sensor problem, not a crankshaft problem.
Crankshaft vs camshaft
| Crankshaft | Camshaft | |
|---|---|---|
| Job | Turns piston motion into rotation | Opens and closes the valves |
| Location | Bottom of the engine block | Cylinder head (overhead cam) or block (pushrod) |
| Speed | Engine speed | Half engine speed in a four-stroke |
| Driven by | The pistons, via the connecting rods | The crankshaft, via a belt, chain or gears |
| Shape | Offset crankpins and counterweights | Row of egg-shaped lobes |
How to tell if a crankshaft is bad
The crankshaft itself rarely fails without warning. Most problems show up as bearing trouble first. Signs worth taking seriously include:
- A deep knocking noise from the bottom of the engine that rises with rpm. It is often louder under load.
- Low oil pressure or an oil pressure warning light, especially when hot.
- Metal particles or glitter in the oil or in the oil filter.
- New vibration that wasn’t there before.
- Excessive fore-and-aft movement of the crank pulley (end play), which can mean thrust bearing wear.
A knock with low oil pressure is a reason to stop driving. Continuing can turn a bearing problem into a ruined crank or a broken rod. Our guide on what destroys a crankshaft covers the causes in detail.
Can a damaged crankshaft be repaired?
Often, yes, depending on the damage. Common options at an engine machine shop are:
- Polishing. Light scuffing on the journals can sometimes be polished out.
- Regrinding. The journals are ground to a slightly smaller, standard undersize and fitted with matching oversize-thickness bearings. The fillets have to be restored properly, or the crank can crack later.
- Welding or metal spraying and regrinding. It is sometimes done on larger or harder-to-replace cranks.
- Straightening. A slightly bent crank can sometimes be straightened by a specialist.
- Replacement. If the crank is cracked, badly overheated or worn beyond the allowed undersize, replacement is usually the only safe choice.
Before any of this, a good shop will check the crank for cracks, often with magnetic particle inspection, and measure it for straightness and journal size.
What drives the cost of crankshaft repair
No single price applies, but a few factors decide the bill:
- Labor to remove the crank. It almost always means removing the engine and taking apart the bottom end. This is usually the biggest cost.
- Machine shop work. Inspection, grinding, polishing and balancing.
- Parts. New bearings at a minimum, plus gaskets, seals and often oil pump and rod bolts.
- Collateral damage. If a bearing failure sent metal through the engine, the block, rods, oil pump and other parts may also need work.
Because of that labor, many owners of everyday cars find that a used or remanufactured engine costs about the same as a crankshaft repair, or less. Get a written estimate that covers both options before deciding.