Engine Parts

Engine Parts and Functions: A Labeled Guide to What's Inside

A labeled guide to engine parts and what each one does, from the block, pistons and crankshaft to the valvetrain and support systems, plus engine bay layout.

On this page
  1. The main parts of an engine, in short
  2. How the parts work together: the four-stroke cycle
  3. A labeled diagram of a piston engine
  4. The bottom end: block, pistons, rods and crankshaft
  5. The top end: cylinder head and valvetrain
  6. The systems that keep an engine running
  7. Engine parts quick-reference table
  8. What “reciprocating engine” means
  9. How engines are described: displacement and cylinder layout
  10. Engine bay layout: what you see under the hood
  11. What damages an engine most
  12. How to find out which engine your car has

The main parts of an engine, in short

A typical car engine is a piston engine. It burns fuel inside sealed cylinders and turns the pressure from that burning into rotation. If you only remember five parts, make them these:

  1. Engine block. The main casting that holds the cylinders and the crankshaft.
  2. Pistons. They slide up and down in the cylinders and take the push from combustion.
  3. Crankshaft. It turns the pistons’ up-and-down motion into rotation.
  4. Cylinder head. It seals the top of the cylinders and holds the valves.
  5. Camshaft. It opens and closes the valves at the right moments.

Everything else either connects those parts or supports them. Connecting rods, rings and bearings do the connecting. Intake, fuel, ignition, exhaust, oil, cooling and electronics do the supporting. The rest of this guide covers each group in turn.

How the parts work together: the four-stroke cycle

Most car engines are four-stroke engines. Each cylinder repeats the same four steps:

  1. Intake. The piston moves down and the intake valve opens. Air, or an air-fuel mixture, is drawn into the cylinder.
  2. Compression. Both valves close and the piston moves up, squeezing the charge.
  3. Power. The mixture ignites, from a spark plug in a gasoline engine or from the heat of compression in a diesel. The expanding gas pushes the piston down.
  4. Exhaust. The exhaust valve opens and the piston moves up, pushing the burned gas out.

One full cycle takes two turns of the crankshaft, or 720 degrees. Only one of the four strokes produces power. The crankshaft, flywheel and the other cylinders carry the engine through the other three. Our guide to crankshaft parts and crank angle shows how those 720 degrees are shared out between cylinders.

A labeled diagram of a piston engine

Here is a simplified stack of a single cylinder, from top to bottom. Real engines have several cylinders side by side, but the order of parts is the same.

┌──────────────────────────────────────┐
│  Valve cover                         │
│  Camshaft(s) + lifters / rockers     │  ← TOP END
│  Valve springs + intake/exhaust      │     (cylinder head)
│  valves                              │
│  Cylinder head + combustion chamber  │
│  (spark plug or injector)            │
├──────── Head gasket ─────────────────┤
│  Cylinder bore                       │
│  Piston + piston rings               │  ← ENGINE BLOCK
│  Wrist pin (piston pin)              │
│  Connecting rod                      │
│  Crankshaft + main bearings          │  ← BOTTOM END
├──────────────────────────────────────┤
│  Oil pan (sump) + oil pump pickup    │
└──────────────────────────────────────┘
   Front of engine: timing belt/chain, harmonic balancer, accessory belt
   Rear of engine: flywheel or flexplate → transmission

Mechanics often talk about the bottom end (block, crankshaft, rods, pistons) and the top end (head, valves, camshafts). The two halves are joined at the head gasket.

The bottom end: block, pistons, rods and crankshaft

Engine block and cylinders

The block is the engine’s backbone. It is usually cast iron or aluminum alloy. It contains the cylinders, which are smooth round bores the pistons slide in. Aluminum blocks often have iron liners or special bore coatings. The block also contains passages called water jackets that carry coolant around the cylinders, and oil galleries that carry pressurized oil to the bearings.

The lower part of the block is the crankcase, where the crankshaft sits in the main bearing saddles. Main caps or a one-piece bedplate bolt underneath to hold the crank in place.

Pistons and piston rings

A piston is a cylindrical plug, usually made of aluminum alloy, that moves up and down in its bore. Its top, the crown, takes the pressure and heat of combustion. The skirt below helps keep the piston square in the bore.

Grooves near the top of the piston hold the piston rings. Most car engines use three per piston: two compression rings and one oil control ring. The rings seal combustion pressure above the piston, scrape excess oil off the cylinder wall, and carry heat from the piston into the block. Our piston rings explainer covers how each ring works and what worn rings look like.

Connecting rods and wrist pins

Each piston is joined to the crankshaft by a connecting rod. The small end of the rod holds the wrist pin (also called the piston pin or gudgeon pin), which lets the piston pivot. The big end clamps around a crankpin on the crankshaft, with a split bearing in between.

The rod takes huge loads in both directions, squeezed on the power stroke and stretched as it reverses direction at high rpm. Our article on connecting rods and why they break explains rod design, materials and failure.

Crankshaft, bearings and flywheel

The crankshaft runs along the bottom of the engine. It is a shaft with offset crankpins (rod journals), one for each rod or pair of rods in a V engine. As the pistons push the rods down, the offset pins turn the shaft, much like your feet turning bicycle pedals. This is the part that turns reciprocating (back-and-forth) motion into rotary motion.

The crank spins on main bearings: replaceable shells that ride on a thin film of pressurized oil, not on bare metal. At the front, the crank drives the timing belt or chain and the accessory belt, usually through a harmonic balancer (torsional damper). At the back it bolts to a heavy flywheel (manual transmissions) or a thinner flexplate (automatics). That passes power to the transmission and helps smooth out the pulses between power strokes.

For the crankshaft’s individual parts and crank angle, see our crankshaft parts and function guide.

Oil pan

The oil pan, or sump, bolts to the bottom of the block and holds the engine oil. The oil pump pulls oil up through a pickup tube and screen, sends it through the oil filter, and pushes it through the galleries to the bearings, camshafts and other moving parts. Then it drains back to the pan.

The top end: cylinder head and valvetrain

Cylinder head and head gasket

The cylinder head bolts to the top of the block and closes off the cylinders. The shaped space above each piston is the combustion chamber. The head contains the intake and exhaust ports (passages for air in and exhaust out), the valves, and usually the camshafts. It also holds the spark plugs in a gasoline engine, or the injectors in most modern diesels and direct-injection gasoline engines.

The head gasket sits between the head and block. It has to seal combustion pressure, coolant and oil from each other all at once. A failed head gasket can let coolant into the cylinders or oil, or let combustion gas into the cooling system.

Valves and valve springs

Each cylinder has at least one intake valve and one exhaust valve. Many modern engines use four valves per cylinder (two intake, two exhaust) for better airflow. The valves are mushroom-shaped. They seal against hardened valve seats in the head and are held shut by valve springs until the camshaft pushes them open.

Camshafts, lifters and rockers (OHV, SOHC, DOHC)

A camshaft is a shaft with egg-shaped lobes. As it turns, each lobe pushes a valve open and then lets the spring close it. In a four-stroke engine the camshaft turns at half crankshaft speed, because each valve opens once every two crank revolutions.

There are three common arrangements:

  • OHV (overhead valve, or “pushrod”). One camshaft sits in the block. Lifters and long pushrods carry the motion up to rocker arms in the head, which press the valves open. This layout is compact and still common in some large-displacement V8s.
  • SOHC (single overhead cam). One camshaft per cylinder head operates both intake and exhaust valves, often through rocker arms.
  • DOHC (dual overhead cam). Two camshafts per head, one for the intake valves and one for the exhaust valves. This is the most common layout in modern car engines and makes it easier to fit four valves per cylinder and variable valve timing.

Lifters (tappets) sit between the cam lobe and the rest of the valvetrain. Many engines use hydraulic lifters that take up clearance automatically using oil pressure. Others use solid lifters or shims that need occasional adjustment.

Timing belt or timing chain

The crankshaft and camshafts must stay exactly in step. If they don’t, the valves open at the wrong time. In many engines a valve that opens at the wrong moment can be hit by the piston. Engines where this can happen are called interference engines.

A toothed rubber timing belt or a metal timing chain (sometimes gears) links them. Belts are usually replaced at the interval the manufacturer gives. Chains are designed to last longer but can stretch, and their tensioners and guides can wear.

The systems that keep an engine running

The core parts above make the engine turn. These systems let it keep running.

  • Air intake. The air filter, intake duct, throttle body (which controls airflow in most gasoline engines) and intake manifold deliver air to each cylinder. A turbocharger or supercharger can force in extra air for more power from a smaller engine.
  • Fuel system. A pump, fuel lines and fuel injectors meter fuel. Injectors may spray into the intake ports (port injection) or straight into the cylinder (direct injection).
  • Ignition. Gasoline engines fire spark plugs, usually through one ignition coil per cylinder on modern engines. Diesels have no spark plugs. They compress air until it is hot enough to ignite the injected fuel, and use glow plugs to help cold starts.
  • Exhaust. The exhaust manifold, catalytic converter, muffler and pipes carry spent gas away and clean it up. Diesels add a particulate filter and often other aftertreatment.
  • Lubrication. Pump, filter, galleries and oil keep metal parts apart on a film of oil. They also carry away heat.
  • Cooling. The water pump circulates coolant through the block and head to the radiator. A thermostat controls engine temperature, and a fan pulls air through the radiator at low speed.
  • Sensors and the ECU. The engine control unit (ECU) reads crank and cam position, airflow, temperatures, oxygen content in the exhaust and more. It uses them to set fuel and spark many times per second. Our engine sensors guide explains what each sensor does and how it fails.
  • Charging and starting. The alternator, driven by the accessory belt, charges the battery. The starter motor cranks the engine until it fires.

Engine parts quick-reference table

Part Where it is What it does Common trouble signs
Engine block Main casting Holds cylinders, crank, coolant and oil passages Cracks, coolant or oil leaks
Cylinder In the block Bore the piston slides in Wear, scoring, oil burning
Piston In each cylinder Takes combustion pressure Knocking, cracked crown
Piston rings Grooves in the piston Seal gas, control oil, move heat Blue smoke, oil use, low compression
Wrist pin Through piston and rod Lets piston pivot on rod Light, rapid knock
Connecting rod Piston to crank Transfers force to crank Deep “rod knock”
Crankshaft Bottom of block Turns piston motion into rotation Knocking, vibration, low oil pressure
Main/rod bearings Around crank journals Carry the crank on an oil film Knocking, metal in oil
Flywheel/flexplate Rear of crank Smooths rotation, drives transmission Vibration, starter grinding
Harmonic balancer Front of crank Damps crank twisting vibration Wobbling pulley, belt issues
Cylinder head On top of block Holds valves, ports, chambers Warping, cracks, leaks
Head gasket Between head and block Seals gas, coolant and oil Overheating, white smoke, coolant loss
Valves In the head Let air in and exhaust out Misfire, low compression, ticking
Valve springs Around valve stems Close the valves Misfire at high rpm
Camshaft Head (OHC) or block (OHV) Opens valves on time Ticking, rough running
Lifters/rockers Between cam and valves Transmit cam motion Ticking or tapping
Timing belt/chain Front of engine Keeps cam(s) and crank in sync Rattle (chain), no-start or damage if broken
Oil pan Under the block Holds the oil Leaks
Oil pump Usually low in engine Pressurizes oil Low oil pressure warning
Intake manifold On the head Delivers air to each cylinder Vacuum leaks, rough idle
Throttle body Front of intake Controls airflow (gasoline) Rough idle, stalling
Fuel injectors Intake or cylinder Meter fuel Misfire, rough idle
Spark plugs/coils In the head Ignite the mixture (gasoline) Misfire, poor economy
Exhaust manifold On the head Collects exhaust Ticking leak, smell
Turbocharger On exhaust side Forces in extra air Low boost, smoke, whine
Water pump Front of engine Circulates coolant Leaks, overheating
Thermostat Coolant outlet Regulates temperature Overheating or slow warm-up
Radiator Front of car Sheds heat from coolant Overheating, leaks
Alternator Accessory belt Charges the battery Battery light, dim lights
Starter motor Near flywheel Cranks the engine Clicking, no crank
ECU Engine bay or cabin Controls fuel, spark and more Warning lights, odd behavior

What “reciprocating engine” means

Reciprocating means moving back and forth in a straight line. A reciprocating engine, or piston engine, is any engine whose pistons slide back and forth in cylinders. Car, motorcycle, lawn mower and most small aircraft engines are reciprocating engines. Jet turbines and Wankel rotary engines are not.

The core parts of any reciprocating engine are the same: cylinders, pistons, connecting rods, a crankshaft, a way to let gas in and out (valves or ports), and a crankcase to hold it all. The part that converts the pistons’ reciprocating motion into rotary motion is the crankshaft, with the connecting rods linking the two. In a light aircraft the crankshaft drives the propeller instead of a gearbox and wheels. The working principle is otherwise much the same.

How engines are described: displacement and cylinder layout

Two labels come up constantly.

Displacement is the total volume all the pistons sweep as they move from bottom to top. It is given in cubic centimeters (cc) or liters. 2000cc means 2,000 cubic centimeters, the same as a 2.0-liter engine. In a four-cylinder engine, each cylinder sweeps roughly 500cc. Displacement is a rough guide to how much air an engine can breathe. It is not a direct measure of power, because turbocharging and engine design make a big difference.

Cylinder count and layout describe how many cylinders there are and how they are arranged:

  • Inline (straight). All cylinders in one row, such as an inline-four (I4) or straight-six. The inline-four is the most common car engine.
  • V. Two banks of cylinders sharing one crankshaft, forming a V: V6, V8, V12. Our article on what V6, V8 and V12 mean explains the trade-offs.
  • Flat or boxer. Two banks lying flat on opposite sides of the crank, used by Subaru and Porsche.

Engine bay layout: what you see under the hood

The space where the engine sits is usually called the engine bay or engine compartment. You reach it by opening the hood (the bonnet in British English). The most common layout for everyday cars is a front-mounted inline-four driving the front wheels.

Transverse vs longitudinal

  • Transverse. The engine sits sideways, with the crankshaft running left to right across the car. This is standard on most front-wheel-drive cars because the engine and transmission package compactly between the front wheels.
  • Longitudinal. The engine sits front to back, with the crankshaft running along the length of the car. This is common on rear-wheel-drive cars, many trucks, and some all-wheel-drive designs.

Knowing which you have helps you make sense of the bay. On a transverse engine, the timing cover and accessory belt are usually on one side, near a front wheel. On a longitudinal engine they face the radiator.

Common under-hood landmarks

Most modern engines sit under a plastic cover, but the parts an owner usually needs to find are similar from car to car:

  • Oil filler cap on the valve cover, often marked with an oil-can symbol
  • Oil dipstick, often with a brightly colored handle (some newer cars have no dipstick and show oil level electronically)
  • Coolant reservoir, a translucent plastic tank with min/max marks
  • Brake fluid reservoir, usually near the driver’s side at the back of the bay
  • Washer fluid reservoir, often with a windshield symbol on the cap
  • Air filter box, a large plastic housing connected to the throttle body by a duct
  • Battery and the fuse/relay box
  • Radiator and cooling fan at the very front
  • Accessory (serpentine) belt driving the alternator, water pump on many engines, A/C compressor and sometimes power steering

Your owner’s manual will have a labeled picture of the engine bay for your specific car. It is the best place to confirm what each cap and tank is before you add anything.

Can you spray down an engine bay?

Many people do clean their engine bays with water, but it calls for care. General precautions are:

  • let the engine cool fully
  • avoid aiming a pressure washer directly at electrical connectors, the alternator, the fuse box or the air intake
  • use gentle pressure and a degreaser made for engines
  • let everything dry before starting

Some manufacturers advise against washing the engine bay at all. Check your owner’s manual first. If you aren’t sure, wiping down with a damp cloth is the cautious option.

What damages an engine most

Most serious engine damage traces back to a few causes:

  • Lack of oil or oil pressure. Bearings, the crankshaft and the camshafts depend on a constant oil film. Running low on oil, or ignoring an oil pressure warning, can ruin an engine quickly. See what destroys a crankshaft for how this plays out in the bottom end.
  • Overheating. It can warp the cylinder head, blow the head gasket and scuff pistons.
  • Skipped maintenance. Old oil, clogged air filters and overdue timing belts all shorten engine life.
  • Detonation (knock). Uncontrolled combustion hammers pistons, rings and bearings.
  • Water or debris ingestion. Driving through deep water can draw water into the cylinders. Water does not compress, so it can bend connecting rods (hydrolock).

Watching the oil level, the temperature gauge and the warning lights catches most of these problems before they turn into major repairs.

How to find out which engine your car has

There are a few reliable ways to identify the engine fitted to your car:

  • Owner’s manual or registration documents. They often list the engine size and type.
  • Under-hood labels. Many cars have an emissions or information label in the engine bay that lists the engine displacement and family.
  • VIN. On many vehicles, one character of the 17-character vehicle identification number identifies the engine. In North America it is often the eighth character. A free online VIN decoder or a dealer can tell you what it means.
  • Engine code on the block. Most engines have a stamped or cast code on the block itself, though it can be hard to see.

Once you know the engine, you can look up its layout, valvetrain type and service intervals. Those facts tell you a lot about which of the parts above matter most for keeping it healthy.

Keep exploring

Guides from other topics

All topics →