The short answer
Car engines are usually described in several ways at once. A label like “turbocharged 2.0-litre inline-four, mounted transversely at the front” tells you five separate things: the cylinder layout (inline), the number of cylinders (four), the displacement (2.0 litres), how air is fed in (turbocharged), and where and which way the engine sits in the car.
Most combustion-engined cars on the road today use an inline-three, inline-four, V6, inline-six or V8. Flat (boxer) engines from Subaru and Porsche are the best-known alternatives. W engines and Wankel rotaries are much rarer, and electric cars replace the engine with motors entirely.
This guide walks through each way of classifying an engine, and links to deeper articles on specific types.
How engines are classified
It helps to treat each label as an answer to a different question:
| Way of classifying | Common options | What it mostly affects |
|---|---|---|
| Cylinder layout | Inline, V, flat (boxer), W, VR | Size, shape, smoothness, cost |
| Cylinder count | 3, 4, 5, 6, 8, 10, 12, 16 | Smoothness, power potential, cost |
| Fuel and ignition | Gasoline (spark), diesel (compression) | Torque, efficiency, fuel type |
| Operating cycle | Four-stroke, two-stroke | Nearly all modern cars are four-stroke |
| Aspiration | Naturally aspirated, turbocharged, supercharged | Power from a given size, response |
| Placement | Front, mid or rear; transverse or longitudinal | Handling, cabin space, drivetrain |
| Non-piston designs | Wankel rotary, gas turbine | Rare in cars |
These categories are independent. A V6 can be gasoline or diesel, turbocharged or not, and mounted sideways or lengthways.
Cylinder layouts
The layout describes how the cylinders are arranged around the crankshaft. It has a big effect on the engine’s shape, how smoothly it runs, and which cars it fits into.
Inline (straight) engines
“Inline” and “straight” mean the same thing: all the cylinders stand in a single row along one crankshaft, usually under one cylinder head. An inline-four is also called a straight-four, I4 or L4.
Some guides describe a “straight” engine as one pointing front-to-back and an “inline” engine as one mounted sideways. That mixes up two different ideas. Which way the engine points is a question of placement, covered further down, not of layout.
Inline engines are simple and relatively cheap to build because they need only one cylinder head and one set of camshafts. The downside is length: every extra cylinder makes the engine longer, which is why inline engines above six cylinders are almost unknown in cars.
- Inline-three: common in small cars, usually turbocharged. See our article on how three-cylinder engines work and whether they’re reliable.
- Inline-four: the most common car engine layout.
- Inline-five: rare, used notably by Audi and Volvo.
- Inline-six: famous for smoothness. Our inline-6 guide explains why it is so well balanced.
V engines
A V engine splits its cylinders into two rows, called banks, set at an angle to each other and sharing one crankshaft. Seen from the front, the banks form a V. Angles of 60 and 90 degrees are common, though others are used.
Folding the cylinders into two banks makes the engine much shorter than an inline engine with the same number of cylinders. That is why V6, V8, V10 and V12 engines are the usual way to fit six or more cylinders into a car. The trade-off is width and complexity: a V engine needs two cylinder heads and usually more camshafts.
V8s come in two main crankshaft designs, which change their sound and character. Our article on flat-plane vs cross-plane crank V8s covers the difference. If you are choosing between engine options on a new car, our comparison of 4-cylinder and V6 engines may help.
Flat (boxer) engines
A flat engine lays its cylinders down horizontally on opposite sides of the crankshaft. In a true boxer, each pair of opposing pistons moves in and out at the same time, like a boxer’s fists, and their forces largely cancel each other out.
Flat engines are low and short but wide. The low height helps lower a car’s centre of gravity. Subaru and Porsche are the best-known users today, and the original Volkswagen Beetle used an air-cooled flat-four. Our article on how boxer engines work and why Subaru and Porsche use them goes into detail.
W and VR engines
Volkswagen developed the VR engine, a V with a very narrow angle between its banks so that both rows of cylinders fit under a single cylinder head. The VR6 is the best-known example.
A W engine joins more than two banks on one crankshaft. Volkswagen’s W8, W12 and W16 are essentially two VR-style engines sharing a crankshaft, which packs many cylinders into a compact block. The W16 powered the Bugatti Veyron and Chiron. See our explainer on how VW’s W8, W12 and W16 are built.
Rotary (Wankel) engines
A Wankel rotary engine has no pistons or cylinders in the usual sense. A rounded triangular rotor spins inside an oval-like housing, and the spaces between the rotor and housing act as moving combustion chambers. Mazda is the company most associated with the design, from the RX-7 and RX-8 sports cars to its current use as a range extender.
Rotaries are compact, smooth and rev freely, but they tend to use more fuel and oil than piston engines. Read how rotary (Wankel) engines work, and for a racing angle, why F1 cars don’t use rotary engines.
Cylinder counts: from three to sixteen
The number of cylinders is the other half of an engine’s basic description.
| Cylinders | Usual layout in cars | Typical use |
|---|---|---|
| 3 | Inline | Small cars and compact crossovers, often turbocharged |
| 4 | Inline (sometimes flat) | Most mainstream cars, crossovers and small trucks |
| 5 | Inline | Rare; some Audi, Volvo and older Ford/Fiat-group models |
| 6 | Inline, V or flat | Midsize and luxury cars, SUVs, pickups, sports cars |
| 8 | V | Pickups, muscle cars, luxury and performance cars |
| 10 | V | Rare; some supercars and heavy-duty trucks |
| 12 | V (or W) | Luxury cars and exotics |
| 16 | W | Bugatti hypercars |
In general, more cylinders means each cylinder can be smaller, and power pulses arrive more often, which tends to make an engine smoother. More cylinders also means more parts, more friction, more weight and more cost. Turbocharging has let smaller engines replace larger ones in many cars, so cylinder count is no longer a reliable guide to power.
Odd numbers of cylinders and very large counts do exist outside cars. Our answers to whether a 7-cylinder engine exists and whether there is a V24 engine cover the unusual ones.
Fuel and ignition: gasoline vs diesel
Most car engines burn either gasoline (petrol) or diesel, and the two ignite their fuel differently.
- Gasoline engines use a spark plug to ignite a compressed mixture of air and fuel. They generally rev higher, are lighter and cost less to build.
- Diesel engines have no spark plugs. They compress air so much that it becomes hot enough to ignite the fuel as it is injected. This needs higher compression ratios and stronger construction. Diesels usually produce more torque at low engine speeds and are often more fuel-efficient, especially under load, which is why they are common in trucks and towing vehicles.
Modern diesels need extra emissions equipment, such as particulate filters and, in many cases, a urea-based fluid system to reduce nitrogen oxides. Some engines are also built or converted to run on alternative fuels such as natural gas or LPG; these are generally spark-ignition engines.
Four-stroke vs two-stroke
Almost every modern car engine is a four-stroke: each cylinder goes through intake, compression, power and exhaust over two turns of the crankshaft.
A two-stroke engine completes its cycle in one turn of the crankshaft, so each cylinder fires once per revolution. Two-strokes are simple and light, but in small gasoline form they are harder to make clean and efficient. They were used in some older cars, such as early Saabs and the East German Trabant, and are still found in some small engines. At the other extreme, many of the largest marine diesel engines in the world are slow-speed two-strokes.
Aspiration: naturally aspirated, turbocharged and supercharged
Aspiration describes how air gets into the cylinders.
- Naturally aspirated engines rely on the pistons drawing air in at atmospheric pressure.
- Turbocharged engines use a turbine spun by exhaust gas to drive a compressor that pushes extra air into the engine. More air allows more fuel to be burned, so a small turbo engine can match a larger naturally aspirated one.
- Supercharged engines drive the compressor mechanically, usually with a belt from the crankshaft, or in some newer designs with an electric motor.
The move toward smaller turbocharged engines, often called downsizing, is why many cars that once offered a V6 now use a turbocharged four-cylinder instead.
Where the engine sits: car engine placement
Placement has two parts: where the engine is along the length of the car, and which way it faces.
Front, mid and rear engine
- Front engine: the engine sits under the bonnet (hood) ahead of the cabin. This is by far the most common arrangement, used in most cars, SUVs and pickups. It leaves the cabin and cargo areas free and is generally the easiest to cool and service. When the engine sits behind the front axle line, it is sometimes called front-mid-engined.
- Mid engine: the engine sits between the front and rear axles, usually just behind the seats. Concentrating the heaviest part of the car near its middle helps handling, so this layout is common in sports cars and supercars, including the current Chevrolet Corvette. It costs passenger and luggage space.
- Rear engine: the engine sits behind the rear axle. The Porsche 911 and the original Volkswagen Beetle are the classic examples. Extra weight over the driven rear wheels helps traction, but the car’s handling needs careful engineering.
Transverse vs longitudinal mounting
- Transverse engines are mounted sideways, with the crankshaft running across the car. This is the normal arrangement in front-wheel-drive cars because the engine and transmission can sit side by side and drive the front wheels directly. It saves a lot of space.
- Longitudinal engines point front-to-back, with the crankshaft running along the car. This is typical of rear-wheel-drive cars, many all-wheel-drive cars, and trucks.
Layout and placement interact. A long inline-six is hard to fit sideways in a typical engine bay, so it is usually mounted lengthwise. A compact V6 fits sideways more easily, which is one reason V6s became the usual six-cylinder choice in front-wheel-drive cars.
Hybrids and electric cars
A hybrid pairs a combustion engine, which can use any of the layouts above, with one or more electric motors and a battery. Plug-in hybrids have a larger battery that can be charged from an outlet for longer electric-only driving.
A fully electric car has no engine at all. It uses electric motors, typically mounted at the front axle, the rear axle or both, powered by a battery pack usually stored under the floor. Some electric cars carry a small engine purely to generate electricity, known as a range extender. Mazda, for example, uses a single-rotor Wankel engine in this role.
Engines beyond cars: radials and gas turbines
Some important engine types are rarely found in cars but are central to aviation and industry:
- Radial engines arrange their cylinders in a circle around the crankshaft, like the spokes of a wheel. They powered many propeller aircraft. Early aircraft “rotary” engines went further and spun the whole cylinder block around a fixed crankshaft. Read how radial and rotary aircraft engines work.
- Gas turbines burn fuel continuously and use spinning compressors and turbines instead of pistons. They power jet aircraft, helicopters, ships and power stations. See how gas turbine engines work.
Common questions
What does 2000cc mean, and is 1.5 L the same as 1500cc?
The cc figure is the engine’s displacement: the total volume swept by all the pistons as they move from the bottom to the top of their cylinders, measured in cubic centimetres. A 2000cc engine displaces about 2 litres, since 1,000 cc equals 1 litre.
So yes, a 1.5-litre engine is roughly 1500cc. Manufacturers round the figure, so a “1.5” might actually measure something like 1,496 or 1,498 cc. Displacement gives a rough sense of an engine’s size, but turbocharging and design matter so much that it is no longer a reliable guide to power.
Where can you find the engine size on your car?
Common places to check include:
- The owner’s manual or the manufacturer’s specification sheet for your model
- Your registration or title documents, which in many countries list the engine size
- Badges on the car’s body, though these are not always accurate or present
- The emissions information label under the bonnet, which on many vehicles states the displacement
- A VIN decoder, since the vehicle identification number usually encodes the engine type
What do you call the place where the engine sits?
It is usually called the engine bay or engine compartment. In everyday speech many people simply say “under the hood” or “under the bonnet.” In mid- and rear-engined cars, the engine bay is behind the cabin rather than in front of it.
Can you drive with a bad engine mount?
Engine mounts hold the engine to the car’s frame and absorb its vibration. A worn mount usually shows up as clunks when accelerating or shifting, more vibration than usual, or the engine visibly rocking.
A car with a slightly worn mount may still be driveable for a short trip to a repair shop. However, a badly failed mount can let the engine move far enough to strain hoses, wiring, the exhaust or the driveshafts. It is best to have a suspected mount problem inspected promptly rather than keep driving on it.