Torque and power in one paragraph each
Torque is a twisting force: force multiplied by the distance from the center of rotation. For an engine, it’s the twisting effort at the crankshaft, produced by combustion pressure pushing the pistons down and the connecting rods turning the crank. An engine’s torque changes with engine speed, so a single torque figure is the peak value at a particular rpm.
Power is the rate of doing work, meaning how much torque is delivered and how fast. An engine making moderate torque at high rpm can produce more power than one making lots of torque at low rpm. That’s why power and torque are both quoted with an rpm figure on a spec sheet. If you’re new to the abbreviations, start with our guide to reading engine specs.
Torque units
The most common torque units for engines are:
- Newton-meter (N·m or Nm): the SI unit, used in most of the world.
- Pound-foot (lb-ft, lbf·ft): used in the US and UK. You’ll also see “ft-lb”. Strictly speaking, foot-pounds is often reserved for work or energy, but in everyday automotive use the two are used interchangeably.
- Kilogram-force meter (kgf·m or kg·m): found in older Japanese and some other specifications.
- Pound-inch (lb-in): used for small fastener torque specs, not engine output.
Conversion table
| From | To | Multiply by |
|---|---|---|
| Nm | lb-ft | 0.7376 |
| lb-ft | Nm | 1.3558 |
| kgf·m | Nm | 9.807 |
| kgf·m | lb-ft | 7.233 |
| lb-in | Nm | 0.1130 |
So 200 Nm is about 148 lb-ft, and 400 lb-ft is about 542 Nm.
What 500 lb-ft actually means
500 lb-ft of torque is the twisting effort you’d get from a 500-pound force on the end of a 1-foot lever, or 250 pounds on a 2-foot lever. That’s about 678 Nm. In passenger vehicles, figures at this level are usually associated with large V8s, high-output turbocharged engines and pickup-truck diesels. For an everyday comparison, see whether 200 Nm of torque is good for a car.
How power is calculated from torque
In imperial units:
Horsepower = torque (lb-ft) × rpm ÷ 5,252
In metric units:
Power (kW) = torque (Nm) × rpm ÷ 9,549
For example, 300 lb-ft at 5,000 rpm is 300 × 5,000 ÷ 5,252 ≈ 286 hp. And 300 Nm at 4,000 rpm is 300 × 4,000 ÷ 9,549 ≈ 126 kW, about 169 hp.
Why 5252?
One mechanical horsepower was defined as 33,000 foot-pounds of work per minute. In one revolution, a torque T (lb-ft) does T × 2π foot-pounds of work. At a given rpm, the work per minute is T × 2π × rpm. Dividing by 33,000 gives horsepower:
hp = T × 2π × rpm ÷ 33,000 = T × rpm ÷ 5,252
(33,000 ÷ 2π ≈ 5,252.) One consequence: on any dyno chart that plots horsepower and lb-ft on the same scale, the two curves always cross at 5,252 rpm.
Metric version
The 9,549 constant comes from the same logic: 60,000 ÷ 2π ≈ 9,549. The 60 converts minutes to seconds and the 1,000 converts watts to kilowatts.
Horsepower units: hp, bhp, PS and kW
- hp (mechanical horsepower): about 745.7 W.
- PS (metric horsepower, also CV or ch): about 735.5 W, roughly 1.4% smaller than hp.
- kW: 1 kW ≈ 1.341 hp ≈ 1.360 PS.
- bhp (brake horsepower): horsepower measured at the crankshaft, explained below.
Brake power: the formula and the dyno
“Brake” power is the power measured at the engine’s output shaft. The name comes from early test methods, such as the Prony brake, which absorbed the engine’s output with friction. Modern engine dynamometers use water brakes, eddy-current units or electric machines, but the idea is the same: load the engine, measure the torque it produces and the speed it turns, and calculate power.
The brake power formula in SI units:
BP (W) = 2π × N × T ÷ 60
where N is engine speed in rpm and T is brake torque in Nm. Dividing by 1,000 gives kW, which is the same as the 9,549 formula above.
Example: an engine produces 250 Nm at 3,000 rpm on the dyno. BP = 2π × 3,000 × 250 ÷ 60 ≈ 78,540 W ≈ 78.5 kW (about 105 hp).
Brake torque
On an engine dynamometer, the absorber housing is free to swing slightly, and a load cell measures the force needed to stop it rotating at a known distance from the shaft center. Brake torque is:
T = F × r
For example, a load cell reading of 400 N at an arm length of 0.5 m means 200 Nm. Modern dynos do this automatically, but the principle hasn’t changed.
Indicated, friction and brake power
Engineers split engine power into three parts:
- Indicated power (IP): the power the gas pressure delivers to the pistons, worked out from cylinder pressure measurements.
- Friction power (FP): the power lost to friction in bearings, piston rings and the valvetrain, plus driving the oil pump, water pump and other accessories, and often pumping losses.
- Brake power (BP): what’s left at the crankshaft. BP = IP − FP.
The ratio BP ÷ IP is the mechanical efficiency. We go further into it, along with thermal and volumetric efficiency, in engine efficiency explained.
BMEP: comparing engines of different sizes
Brake mean effective pressure (BMEP) is the average cylinder pressure that would produce the measured brake torque. It takes displacement out of the comparison, so you can see how hard different-sized engines are working. For a four-stroke engine:
BMEP (bar) ≈ 0.1257 × torque (Nm) ÷ displacement (liters)
A 2.0 L engine making 200 Nm has a BMEP of about 12.6 bar. A 2.0 L turbo making 350 Nm is at about 22 bar. Naturally aspirated gasoline engines commonly peak somewhere around 10–13 bar, while modern turbocharged engines often reach 20 bar or more. Treat these as rough guides, not hard limits.
Reading a power curve
A dyno chart plots torque and power against rpm. Peak figures tell you less than the curve shape, which shows where in the rev range the engine is useful.
Gasoline curve
A typical naturally aspirated gasoline engine’s torque rises to a peak in the mid-range, then falls off as breathing becomes harder at high rpm. Because power is torque × rpm, power keeps climbing after the torque peak and only flattens or drops once torque falls fast enough. That’s why peak power is usually near the top of the rev range, close to the redline.
Diesel curve
Diesel engines tend to show:
- High torque at low rpm, often with a broad, flat plateau. On turbocharged diesels this plateau is shaped largely by the turbo and the engine’s fueling limits.
- A lower rev ceiling. Diesel combustion is slower and diesel components are heavier, so most diesels stop at lower speeds than gasoline engines.
- Power that peaks at a “rated speed” and is then held or cut back by the governor or engine management.
Heavy-duty diesels are often designed to deliver strong torque well below their rated speed, so the engine “pulls” as load increases and rpm drops. Engineers call this torque rise or torque backup. It’s one reason diesels suit towing and heavy vehicles.
Where turbos come in
A turbocharger needs enough exhaust energy to make meaningful boost, so it depends on load as well as rpm. Revving an engine in neutral won’t spool most turbos much. Small modern turbos on car engines are often sized to deliver peak torque from fairly low engine speeds, commonly somewhere in the 1,500–2,000 rpm area. Larger turbos built for high peak power typically come in later. The exact figure varies a lot between engines.
Crank vs wheel figures
Manufacturers quote power at the crankshaft. A chassis dyno measures at the wheels, after the transmission, differential and tires have taken their share. Wheel figures are therefore lower. Rules of thumb for the loss vary widely, often around 10–20%, but it depends on the drivetrain, the dyno and the test method. Comparing crank figures with wheel figures directly is a common source of confusion.