Timing and Valvetrain

Variable Valve Timing, CVVD and Camless Engines

How variable valve timing, cam phasers, variable lift, Hyundai's CVVD and camless engines like Freevalve change valve events to balance power and efficiency.

On this page
  1. Why a fixed camshaft is a compromise
  2. The three things you can vary: timing, lift and duration
  3. Cam phasing (VVT, CVVT and similar)
  4. Cam switching and variable lift
  5. CVVD: continuously variable valve duration
  6. Electro-hydraulic valve control
  7. Camless engines
  8. What variable valve systems mean for owners

Why a fixed camshaft is a compromise

In a conventional engine, the shape of each cam lobe fixes three things about the valve it operates: when it opens, how far it opens, and how long it stays open. Those choices suit some conditions better than others.

  • At idle and low speed, the engine wants little valve overlap and an early intake closing so it runs smoothly and traps as much mixture as possible.
  • At high RPM, it wants longer opening periods, more lift and more overlap so the cylinders can fill while the air is moving quickly.
  • At light cruising load, efficiency improves if the engine can reduce the work it does pulling air past a nearly closed throttle (pumping losses).

A fixed camshaft has to pick one compromise. Variable valve systems let the engine change its valve events as conditions change. (For background on how valve events and overlap work, see our guide to valve overlap and reversion.)

The three things you can vary: timing, lift and duration

Variable valve systems are easiest to understand by what they change:

  • Timing (phase): shifting the whole opening event earlier or later without changing its length.
  • Lift: how far the valve opens.
  • Duration: how many crankshaft degrees the valve stays open.

Most systems vary one or two of these. Fully camless engines can, in principle, vary all three independently, cylinder by cylinder.

Cam phasing (VVT, CVVT and similar)

The most common system on modern engines is cam phasing. Manufacturers give it many names, including VVT, VVT-i, VANOS, CVVT and others, but the basic principle is similar.

How a cam phaser works

The camshaft sprocket isn’t fixed solidly to the camshaft. Instead, a phaser sits between them. A common type is the vane phaser: the camshaft carries a rotor with vanes that sits inside a housing attached to the sprocket. Engine oil is fed to one side of the vanes or the other through an oil control valve (a solenoid) commanded by the engine computer. Pushing oil to one side rotates the camshaft a few degrees ahead of the sprocket (advance); pushing it to the other side rotates it back (retard).

Because the phaser shifts the whole lobe, opening and closing move together. The duration stays the same; only the timing changes. Phasers can be fitted to the intake cam, the exhaust cam, or both.

Since most phasers are oil-operated, they depend on clean oil at the right pressure. Low oil, the wrong viscosity or sludge can make a phaser respond slowly or stick, which typically sets cam timing fault codes and can cause rough running. Some newer engines use electrically driven phasers that respond faster and work even at low oil pressure.

What is Hyundai CVVT? What is Suzuki VVT?

CVVT stands for Continuously Variable Valve Timing, the name used by Hyundai and Kia (among others) for their cam phasing system. “Continuously” means the computer can hold the cam at any angle within its range, rather than switching between two fixed positions.

Suzuki’s VVT is likewise a cam phasing system, generally used on the intake camshaft. In both cases the system changes when the valves open and close, not how far or how long.

Cam switching and variable lift

Another approach is to give each valve more than one cam profile. Cam switching systems, such as Honda’s original VTEC, use a mild lobe for normal driving and engage a more aggressive lobe at higher RPM, usually by locking rocker arms together with an oil-pressure-operated pin. This changes lift and duration in a step rather than continuously.

Continuously variable lift systems go further. BMW’s Valvetronic, for example, uses an extra intermediate lever and a motor-driven eccentric shaft to vary intake lift smoothly from very small to full. At light load the engine can control airflow largely with the valves instead of the throttle, which reduces pumping losses. Hyundai’s CVVL (Continuously Variable Valve Lift) is a similar idea.

CVVD: continuously variable valve duration

CVVD stands for Continuously Variable Valve Duration. Hyundai Motor Group introduced it in 2019 on the Smartstream G1.6 T-GDi, a 1.6-liter turbocharged direct-injection four-cylinder, and described it as the first production engine to vary valve duration continuously.

Earlier systems could move the valve event (CVVT) or change its height (CVVL), but because opening and closing were tied together by the cam profile, they couldn’t stretch or shrink the opening period on its own. CVVD adds a mechanism that changes how quickly the cam lobe sweeps past the valve during the opening event. Speeding the lobe up shortens the effective duration; slowing it down lengthens it. Cam phasing can still shift the event as a whole, so the engine gains an extra degree of freedom.

How CVVD behaves at light and heavy load

Hyundai’s description of the system’s strategy runs roughly like this:

  • At steady, light-load cruising, the intake valve is held open from the middle to the end of the compression stroke. Some of the charge is pushed back out, the engine does less compression work, and efficiency improves. This is similar in principle to an Atkinson-cycle strategy.
  • At high load, the intake valve closes early in the compression stroke to trap as much air as possible, increasing torque.
  • In between, duration is adjusted to suit conditions.

What Hyundai claimed for CVVD

At launch, Hyundai stated that CVVD improved engine performance by about 4% and fuel efficiency by about 5%, and reduced emissions by about 12%, compared with its previous approach. These are manufacturer figures; real-world results depend on the vehicle and how it’s driven. The engine also used low-pressure exhaust gas recirculation and higher-pressure direct injection, so not all of the improvement in the complete package comes from CVVD alone.

Electro-hydraulic valve control

Fiat’s MultiAir (later used across other Stellantis engines) sits between conventional and camless designs. A camshaft still drives the intake valves, but through a small oil-filled hydraulic chamber controlled by a solenoid valve. When the solenoid is closed, the oil acts like a solid link and the valve follows the cam. When it opens, oil escapes, and the valve closes early or opens less, whatever the cam lobe is doing. That allows the engine to vary intake timing, lift and duration cylinder by cylinder, within the limits of the cam profile.

Camless engines

A camless engine removes the camshaft entirely and opens each valve with its own actuator, controlled by the engine computer.

How camless engines work

Instead of a cam lobe pushing on a lifter or follower, each valve (or pair of valves) has an actuator that can be electromagnetic, electro-hydraulic or electro-pneumatic. The computer decides, for every cycle, when each valve opens, how far, and for how long. In principle this allows:

  • Any timing, lift and duration at any speed and load
  • Different valve events in different cylinders
  • Shutting cylinders down completely by keeping their valves closed
  • Running different combustion strategies (for example, Miller- or Atkinson-style cycles) as needed

Freevalve, Camcon and other projects

The best-known example is Freevalve, developed by a company associated with Koenigsegg. Its actuators use compressed air to open the valves, with hydraulic control and electronics managing the motion. Koenigsegg showed a Freevalve-equipped three-cylinder engine for its Gemera.

Camcon Automotive in the UK developed a related idea called intelligent valve actuation, in which an electric actuator rotates a small cam for each valve, so the valve motion is still set mechanically but each cam can be moved independently.

Major manufacturers and suppliers have researched camless valve trains for decades, and a number of prototypes have been shown.

Why camless engines are still rare

Despite the potential, camless engines haven’t reached mass production. Commonly cited challenges include:

  • Cost and complexity: one actuator, sensor and control channel per valve or valve pair
  • Energy use: actuators need power, which offsets some of the efficiency gain
  • Soft landing: valves must close gently onto their seats at every speed to avoid noise and wear
  • High RPM control: the actuators must move valves quickly and precisely at high engine speeds
  • Failure modes: the system must fail safely, particularly in interference engines where an open valve can meet a rising piston (see our article on interference vs non-interference engines)
  • Improving conventional systems: cam phasing, variable lift and electrified powertrains have captured much of the benefit at lower cost

What variable valve systems mean for owners

For most drivers, variable valve timing works invisibly. The main practical points are:

  • Keep the oil clean, full and to specification. Oil-operated phasers and switching systems are sensitive to oil condition.
  • Treat cam timing fault codes seriously. They can point to a sticking phaser or oil control valve, but also to a stretched timing chain or a belt that has jumped a tooth. See what happens if valve timing is incorrect.
  • Phaser rattle at start-up is a known issue on some engines when a phaser’s locking pin wears or oil drains back overnight.

To see how these systems fit into the different camshaft layouts, read about the three types of valve trains, and for the bigger picture of how valve and ignition timing work together, see our engine timing guide.

The complete guide to timing and valvetrain

Engine Timing Explained: Ignition Timing, Valve Timing and Timing Wheels
Read the guide

Keep exploring

Guides from other topics

All topics →