What the Otto cycle is
The Otto cycle is the four-stroke operating cycle used by almost every petrol car engine. It’s named after Nikolaus August Otto, the German engineer whose 1876 engine was the first practical engine to compress its fuel-air charge in the cylinder before igniting it.
“Four-stroke” means the piston makes four movements, down, up, down, up, to complete one cycle. That takes two full turns of the crankshaft. Only one of the four strokes produces power. The other three prepare for it or clean up after it.
If you want the bigger picture of how the cycle fits into a whole car engine, start with how a car engine works.
The four strokes
Two positions come up repeatedly. Top dead centre (TDC) is the piston’s highest point in the cylinder, and bottom dead centre (BDC) is its lowest.
1. Intake
The piston moves down from TDC to BDC with the intake valve open and the exhaust valve closed. The falling piston lowers the pressure in the cylinder, and atmospheric pressure, or a turbocharger, pushes fresh charge in. In a port-injected petrol engine, that charge is air with fuel already mixed in. In a direct-injection engine, it’s mostly air, and fuel is sprayed straight into the cylinder.
2. Compression
Both valves close and the piston rises from BDC to TDC, squeezing the charge into the small combustion chamber. The ratio of the cylinder’s volume at BDC to its volume at TDC is the compression ratio. Petrol car engines typically fall somewhere around 9:1 to 13:1, though some go outside that range. Compression raises the charge’s pressure and temperature, which lets it burn quickly and release more useful work.
3. Power
Shortly before the piston reaches TDC, the spark plug fires. The flame spreads through the mixture, and the pressure in the cylinder rises sharply. That pressure drives the piston down from TDC to BDC. This stroke is also called the expansion or combustion stroke. It’s the only one that adds energy to the crankshaft. The momentum of the flywheel, plus power strokes in other cylinders, carries the engine through the other three.
4. Exhaust
The exhaust valve opens and the piston rises from BDC to TDC, pushing the burnt gases out into the exhaust manifold. Then the exhaust valve closes, the intake valve opens, and the cycle starts again.
The five events of a four-stroke engine
Some textbooks describe the cycle as five events rather than four strokes, because ignition is a separate event that happens at the end of the compression stroke:
- Intake
- Compression
- Ignition
- Power (expansion)
- Exhaust
It’s the same cycle described another way. Ignition just gets its own step. The idea that an engine needs air, fuel and ignition at the right moment is explored in what are the three things that make an engine run.
Real engines: valve timing and overlap
The textbook version has valves opening and closing exactly at TDC and BDC. Real engines don’t work that way, because gases have inertia and take time to flow:
- The intake valve usually opens a little before TDC and closes some way after BDC, letting the moving column of air keep filling the cylinder.
- The exhaust valve usually opens before BDC, near the end of the power stroke. That gives the high-pressure gas a head start out of the cylinder.
- Around TDC between the exhaust and intake strokes, both valves are briefly open at once. This is valve overlap, and it helps outgoing exhaust draw in fresh charge.
The camshaft profile sets these timings. Many modern engines use variable valve timing, which shifts them while the engine runs, trading low-speed smoothness against high-speed power.
Four-stroke engine parts and their functions
| Part | Function |
|---|---|
| Cylinder | The bore the piston slides in; together with the head it forms the working chamber |
| Piston | Forms the moving floor of the combustion chamber and transmits gas pressure to the connecting rod |
| Piston rings | Seal combustion pressure, control oil on the cylinder wall, and pass heat from the piston to the cylinder |
| Connecting rod | Links the piston to the crankshaft |
| Crankshaft | Converts the piston’s up-and-down motion into rotation |
| Flywheel | Smooths out power pulses and stores momentum to carry the engine through non-power strokes |
| Cylinder head | Closes the top of the cylinder and holds the valves, spark plug and ports |
| Intake and exhaust valves | Open and close to let charge in and exhaust out |
| Camshaft | Opens the valves at the right moments; turns at half crankshaft speed |
| Timing belt or chain | Keeps the camshaft in step with the crankshaft |
| Spark plug | Ignites the compressed mixture (petrol engines) |
| Fuel injector | Meters fuel into the port or cylinder |
| Sump (oil pan) | Holds the engine oil |
What is the main function of the piston?
The piston’s main job is to turn gas pressure into force. During the power stroke, combustion pressure pushes on the piston crown, and the piston passes that force through the gudgeon pin and connecting rod to the crankshaft. It also acts as a pump during the other strokes. It draws charge in on the intake stroke, squeezes it on compression and pushes exhaust out. With its rings, it keeps combustion gas above it and oil below it.
The five main components
If you had to pick five core components of a four-stroke engine, a reasonable list would be the cylinder block, cylinder head, piston, connecting rod and crankshaft. Some lists put the camshaft or valves in place of the head. There’s no single official list.
The ideal Otto cycle in theory
Engineers model the Otto cycle as four idealised processes acting on a fixed amount of gas:
- Compression with no heat loss (isentropic compression)
- Heat added instantly at constant volume, standing in for very fast combustion at TDC
- Expansion with no heat loss (isentropic expansion), standing in for the power stroke
- Heat rejected at constant volume, standing in for exhaust and intake
In this ideal model, efficiency depends only on the compression ratio and the gas’s properties. Higher compression gives higher theoretical efficiency. In petrol engines, the practical limit is knock: compress the mixture too much and it can ignite on its own before the flame front reaches it.
Real engines fall well short of the ideal figure because of heat lost to the cylinder walls, combustion that takes time, friction, and the work spent pulling air past a part-closed throttle. Much of that lost heat ends up in the coolant, which is why the cooling system matters so much.
Otto cycle vs diesel cycle: which is more efficient?
The answer depends on what you hold constant:
- At the same compression ratio, the ideal Otto cycle is more efficient than the ideal diesel cycle, because it adds all its heat at the highest compression point.
- In real engines, diesels are usually more efficient. They compress air alone, so there’s no fuel to knock, and they can run much higher compression ratios. They also have no throttle restricting the intake, which cuts pumping losses at part load.
So the diesel engine’s real-world advantage comes mainly from higher compression and the lack of a throttle, not from the cycle itself.
History: Nikolaus Otto and the first four-stroke engine
Otto, working with his business partner Eugen Langen, built the four-stroke compressed-charge engine in 1876, and their company became known as Deutz. Earlier gas engines, such as Étienne Lenoir’s from around 1860, burned their charge without compressing it first, and were very inefficient. Compressing the charge before ignition was the key step forward.
The French engineer Alphonse Beau de Rochas had described the four-stroke principle in a patent in 1862, but he didn’t build a working engine. Otto’s German patent was later challenged and overturned on the basis of that earlier description, which opened the four-stroke design to other manufacturers.
What was the Otto engine used for?
Otto’s early engines were stationary engines that ran on coal gas (town gas) piped in from the gas supply. They powered machinery in small factories and workshops, where a compact engine was far more convenient than a steam plant with a boiler. Engineers who worked at Deutz, notably Gottlieb Daimler and Wilhelm Maybach, went on to develop lighter, faster-running four-stroke engines that ran on liquid fuel and were suitable for vehicles.
Who is the father of the IC engine?
There’s no single agreed answer, because the internal combustion engine developed through many inventors. Nikolaus Otto is most often given the title for the four-stroke engine, because his 1876 engine set the pattern that car engines still follow. Étienne Lenoir is sometimes credited for the first commercially produced internal combustion engine. Rudolf Diesel is the father of the compression-ignition engine.
Are four-stroke engines used in cars?
Yes. Almost every petrol and diesel car engine made today is a four-stroke. Two-strokes were used in some cars in the past, but stricter emissions rules and fuel economy demands have pushed them out of cars. They survive mainly in small equipment, some motorcycles and large marine engines. See how a two-stroke engine works for the contrast.
What is an internal combustion motor? It’s simply another name for an internal combustion engine: a machine that burns fuel inside itself to produce mechanical work. The four-stroke Otto engine is the most common kind. For how it compares with steam and Stirling engines, see internal vs external combustion.