Diesel Engines

Diesel Particulate Filters: How DPF Regeneration Works and Why It Fails

How a diesel particulate filter traps soot, how passive, active and forced DPF regeneration burn it off, why regens fail, and how to keep a DPF healthy.

On this page
  1. What a diesel particulate filter does
  2. How the filter is built
  3. Soot vs ash: what regeneration can and can’t remove
  4. How DPF regeneration works
  5. How the engine knows when to regenerate
  6. Signs a regeneration is happening (and what to do)
  7. Why DPF regeneration fails
  8. Symptoms of a clogged DPF
  9. Cleaning vs replacing a DPF
  10. How to keep a DPF healthy
  11. Is it legal to remove a DPF?

What a diesel particulate filter does

A diesel particulate filter (DPF) is a filter in the exhaust that traps the soot a diesel engine produces. Soot is fine carbon-based particulate matter, the black part of diesel smoke, and it’s harmful to breathe. Modern DPFs typically capture the large majority of soot particles, which is why a healthy, modern diesel’s exhaust looks clear.

Any filter eventually fills up. Regeneration is the process of burning the trapped soot off, at high temperature, so the filter can keep working. Understanding how regeneration works, and what stops it, explains most DPF problems.

The DPF usually sits downstream of a diesel oxidation catalyst (DOC) and, on many vehicles, upstream of an SCR catalyst that uses DEF. For how these fit into the engine as a whole, see how diesel engines work.

How the filter is built

Most DPFs are wall-flow filters: a ceramic honeycomb block, commonly made of cordierite or silicon carbide, with thousands of small parallel channels. The channels are plugged at alternate ends. Exhaust enters a channel that is open at the front but blocked at the back, so the gas has to pass through the porous channel wall into a neighbouring channel to get out. Soot particles are too big to pass through the wall and stay behind on its surface.

This design traps soot very effectively, but as soot builds up, it becomes harder for exhaust to get through. That rising resistance, called back pressure, is what the engine monitors.

Soot vs ash: what regeneration can and can’t remove

Two things build up in a DPF:

  • Soot is carbon, and it burns. Regeneration turns it into carbon dioxide.
  • Ash is the non-combustible residue left behind, mostly from additives in engine oil that burns in the cylinders, plus traces from fuel and engine wear. Ash can’t be burned off.

So regeneration keeps soot under control, but ash slowly accumulates over the life of the filter. Eventually the filter needs to be removed for professional cleaning, or replaced. How long that takes varies widely with the engine, oil consumption, oil type and driving; figures of 100,000 miles or more are often quoted for light-duty vehicles, but there’s no single interval.

How DPF regeneration works

There are three main types of regeneration.

Passive regeneration

Passive regeneration happens automatically during normal driving whenever the exhaust is hot enough, typically during steady highway driving or under heavy load such as towing. The DOC upstream of the filter converts some nitric oxide in the exhaust into nitrogen dioxide (NO₂), which can oxidise soot at lower temperatures than oxygen alone. Exhaust temperatures of roughly 300°C (about 570°F) and above are commonly cited for passive regeneration to work well.

The driver doesn’t notice anything, and no extra fuel is used. Vehicles that spend a lot of time on the highway may rarely need any other kind of regeneration.

Active regeneration

When the engine computer estimates that soot has built up past a set threshold and passive regeneration isn’t keeping up, it starts an active regeneration. It raises exhaust temperature by:

  • Injecting extra fuel late in the cycle (post-injection), so unburned fuel reaches the DOC, or
  • Spraying fuel directly into the exhaust through a separate doser, on some trucks.

The fuel burns on the DOC, heating the exhaust entering the DPF to roughly 550 to 650°C (about 1,000 to 1,200°F), where soot burns quickly with oxygen. The engine may also adjust EGR, the turbo, an intake throttle or idle speed to help.

Active regeneration generally happens while you drive and may take 10 to 30 minutes or more, depending on the vehicle and conditions. It works best when you can keep driving at a reasonable steady speed until it’s finished.

Parked and forced regeneration

If soot gets too high for a normal active regeneration, perhaps because previous ones kept being interrupted, the vehicle may ask for a parked regeneration. On many trucks and some cars, the driver can start this from a switch or menu once conditions are met (parked, brake set, engine warm, enough fuel). The engine runs at elevated speed for a period, often around 20 to 60 minutes, to burn the soot off.

A forced or service regeneration is started by a technician using a scan tool, usually when the filter is too loaded for the driver-initiated process, or after repairs.

Parked and forced regenerations produce very hot exhaust. Do them outdoors, away from buildings, dry grass and anything flammable, and follow the manufacturer’s instructions.

How the engine knows when to regenerate

The engine uses a differential pressure sensor that measures pressure before and after the DPF. As soot builds up, the pressure difference rises. The computer combines that with a soot model based on how the engine has been driven, plus readings from exhaust temperature sensors, to estimate soot load and decide when to regenerate.

That’s why a failed pressure sensor, a cracked sensor hose or a bad temperature sensor can cause DPF warnings or stop regeneration even when the filter itself is fine.

Signs a regeneration is happening (and what to do)

Many vehicles show a dashboard message or light during regeneration. Others give only subtle clues:

  • Idle speed is slightly higher than usual.
  • The cooling fan runs after you switch off.
  • A hot, acrid smell from the exhaust.
  • Slightly higher fuel consumption.
  • Stop-start may stop working temporarily.

If you notice a regeneration in progress, the best thing to do is keep driving at a steady speed until it finishes if it’s safe and practical to do so. Repeatedly switching off mid-regeneration is one of the main causes of DPF clogging. Avoid parking over dry grass or leaves right after a regeneration, because the exhaust is extremely hot.

Why DPF regeneration fails

  • Short trips and urban driving. The exhaust never gets hot enough for passive regeneration, and active regenerations keep getting interrupted.
  • Excessive idling. Low exhaust temperatures and high soot; see why you shouldn’t let diesels idle.
  • Engine faults that make extra soot, such as leaking injectors, boost leaks, a sticking EGR valve or a worn turbo. These overload the filter faster than it can regenerate. Black smoke is a warning sign; see what diesel smoke colours mean.
  • Sensor faults that stop the computer measuring soot load correctly.
  • Oil consumption from worn rings, turbo seals or valve seals, which adds ash and can clog the filter permanently. High blow-by can be a related sign.
  • The wrong engine oil. Engines with DPFs usually require low-ash (“low-SAPS”) oils to the manufacturer’s specification.
  • Coolant or fuel contamination reaching the exhaust, for example from a leaking EGR cooler.
  • Thermal damage. A very heavily loaded DPF that regenerates too hot can crack or melt internally.
  • Low fuel. Some vehicles won’t start an active regeneration when the fuel level is low.

Symptoms of a clogged DPF

  • A DPF warning light or message.
  • Loss of power or limp mode.
  • Very frequent regenerations.
  • Higher fuel consumption.
  • Rising engine oil level on some vehicles, from fuel dilution during repeated post-injection regenerations.
  • Hard starting or rough running in severe cases, because of high back pressure.

For other faults that share these symptoms, see common diesel engine problems.

Cleaning vs replacing a DPF

Options, roughly from least to most invasive:

  1. A long steady drive, if the warning has only just appeared and the manual allows it.
  2. A parked or forced regeneration by the driver or a workshop.
  3. Fixing the underlying fault that’s producing too much soot or stopping regeneration.
  4. Off-vehicle cleaning, where the DPF is removed and cleaned with air pulses, baking or other methods to remove ash.
  5. Replacement, if the filter is cracked, melted, or too contaminated to clean.

Fuel additives and “DPF cleaners” are widely sold; they may help in some cases, but results vary and they don’t remove ash or fix an underlying fault.

How to keep a DPF healthy

  • Drive at steady highway speeds regularly, especially if you mostly do short trips.
  • Don’t switch off during a regeneration if you can avoid it.
  • Use the engine oil specification the manufacturer requires.
  • Fix fuel injection, boost or EGR faults promptly; see common rail diesel injection for injector issues.
  • Keep the fuel tank above a quarter full so active regenerations can run.
  • Respond to DPF warnings early, before the filter is heavily loaded.

If most of your driving is short trips, a diesel may not suit you; see gas vs diesel engines.

On road vehicles, removing or disabling a DPF is generally illegal in the United States under the Clean Air Act, and in the UK, the EU and many other countries. A vehicle with its DPF removed can fail inspections, and in the UK MOT tests check for its presence. The safer and legal route is to repair the cause of the problem and clean or replace the filter.

The complete guide to diesel engines

How Diesel Engines Work: Principle, Parts and the Four-Stroke Cycle
Read the guide

Keep exploring

Guides from other topics

All topics →