The short version
A two-stroke engine completes the full combustion cycle, intake, compression, power and exhaust, in two strokes of the piston, one up and one down. That’s one crankshaft revolution, compared with two for a four-stroke. It does this by overlapping events, and by using ports in the cylinder wall, which the piston itself covers and uncovers, in place of the usual camshaft and valves.
Firing once every revolution makes two-strokes light, simple and strong for their size. The price is higher fuel consumption and emissions, and the need for oil in the fuel. If you’re not yet familiar with the four-stroke cycle it’s compared against, see the four-stroke Otto cycle.
The key idea: the piston does double duty
In a common small two-stroke, such as a chainsaw, strimmer or older dirt bike, both sides of the piston are working:
- Above the piston, the cylinder compresses and burns the charge, just as in a four-stroke.
- Below the piston, the sealed crankcase acts as a pump. As the piston rises, crankcase volume increases and fresh mixture is drawn in. As the piston falls, it squeezes that mixture so it can be pushed up into the cylinder.
This crankcase pumping is what lets the engine skip separate intake and exhaust strokes.
The ports
A typical crankcase-scavenged two-stroke has three kinds of opening:
- Intake port: Lets fresh air-fuel-oil mixture into the crankcase.
- Transfer ports: Passages that connect the crankcase to the cylinder. Their openings in the cylinder wall sit a little lower than the exhaust port.
- Exhaust port: An opening in the cylinder wall that lets burnt gas out into the exhaust.
The piston’s position decides which ports are open. The skirt and crown slide past the openings, uncovering and covering them, so the port heights and shapes effectively set the engine’s “valve timing.”
The cycle, stroke by stroke
Upstroke: compression above, intake below
As the piston rises from the bottom of its stroke:
- It covers the transfer ports, then the exhaust port, sealing the cylinder.
- The charge above it is compressed into the combustion chamber.
- Below it, crankcase pressure drops, and fresh mixture is drawn into the crankcase through the intake.
Just before the piston reaches the top, the spark plug fires.
Downstroke: power, exhaust and transfer
The burning mixture drives the piston down. That’s the power stroke. As it descends:
- The piston squeezes the fresh mixture in the crankcase, and the intake closes.
- Near the bottom, the piston uncovers the exhaust port first. The still-pressurised burnt gas rushes out. This is often called “blowdown.”
- A moment later, the piston uncovers the transfer ports. The compressed fresh charge from the crankcase flows up into the cylinder, helping push the remaining exhaust out ahead of it.
Then the piston starts rising again, and the cycle repeats. Each revolution includes one power stroke.
Scavenging: clearing out the old charge
Scavenging is the process of clearing burnt gas out of the cylinder and replacing it with fresh charge. In a two-stroke, it happens while the exhaust and transfer ports are open at the same time, so it’s never perfect:
- Some burnt gas stays in the cylinder and dilutes the next charge.
- Some fresh mixture flows straight out of the exhaust port before it’s trapped. This is known as short-circuiting. In an engine that mixes fuel with the incoming air, that means unburnt fuel and oil go out with the exhaust. It’s the main reason simple two-strokes use more fuel and pollute more.
Cross, loop and uniflow scavenging
Engineers have developed several ways to direct the gas flow:
- Cross scavenging: Transfer and exhaust ports sit on opposite sides, and a raised deflector on the piston crown steers the incoming charge upwards. It’s an older design.
- Loop scavenging: Transfer ports are angled so the fresh charge sweeps up the far cylinder wall and loops back down towards the exhaust, pushing burnt gas ahead of it. Most modern small two-strokes use this, with a flat or slightly domed piston.
- Uniflow scavenging: Fresh air enters through ports at the bottom of the cylinder and exhaust leaves at the top, usually through a valve, so the gas flows one way. This is the most effective method, and it’s used in large two-stroke diesels.
Controlling the intake: piston port, reed valve, rotary valve
How the crankcase intake opens and closes affects how the engine performs:
- Piston port: The piston skirt opens and closes the intake port. It’s the simplest method, but some mixture can be pushed back out at low speed.
- Reed valve: Thin flexible petals open when crankcase pressure drops and close when it rises, acting as a one-way valve. This widens the useful rev range and is common on motorcycles and outboards.
- Rotary valve: A disc on the crankshaft with a cut-out opens the intake at set points. Used on some racing and performance engines.
The expansion chamber exhaust
Many performance two-strokes use a carefully shaped exhaust called an expansion chamber. Pressure waves bouncing back from its cone-shaped sections help pull exhaust out, and then push escaping fresh charge back into the cylinder just before the port closes. When it’s working at the right engine speed, it can give a large boost in power. That’s why tuned two-stroke bikes are known for a sudden “powerband” at higher revs.
Why two-strokes need oil in the fuel
In a four-stroke, the crankcase holds an oil sump, and a pump circulates oil around the engine. See how engine lubrication works for that system. A crankcase-scavenged two-stroke can’t do this, because its crankcase is full of incoming fuel mixture.
Instead, oil travels with the fuel. The mixture passing through the crankcase leaves a film of oil on the crankshaft bearings, connecting rod, piston and cylinder wall. The oil is then burnt with the fuel, or leaves with the exhaust. This is a total-loss system: the oil isn’t recovered.
It’s delivered in one of two ways:
- Premix: The oil is mixed into the fuel in a fixed ratio before filling the tank.
- Oil injection: A separate oil tank and pump meter oil into the intake or engine, often varying the amount with engine speed and load.
Mixing premix safely
- Use the ratio in the manufacturer’s manual. Common ratios for modern equipment range from about 50:1 to 32:1 (fuel to oil), but don’t guess. Too little oil risks seizing the engine, and too much can cause smoke, fouled plugs and carbon build-up.
- Use oil made for two-stroke engines, not ordinary four-stroke engine oil, and the type specified for your engine (air-cooled or marine, for example).
- Mix in a clean, approved fuel container, and shake it before refuelling, because the oil can settle.
- Don’t store premix too long. Mixed fuel degrades, so mix amounts you’ll use reasonably soon.
Advantages and disadvantages
| Advantages | Disadvantages |
|---|---|
| One power stroke per revolution: high power for size and weight | Higher fuel consumption, because some fresh charge short-circuits |
| Few moving parts, with no camshaft or valvetrain in simple designs | Higher emissions of unburnt hydrocarbons and oil smoke |
| Light, compact and cheap to build | Oil must be mixed or injected, and is burnt rather than reused |
| Runs in almost any orientation, since there’s no oil sump to slosh | Often a narrower usable rev range and rougher idle |
| Simple to maintain | Higher wear in some designs; louder |
Where two-strokes are used today
Tighter emissions rules have pushed two-strokes out of cars and most road motorcycles. They’re still common in:
- Handheld garden and forestry equipment: chainsaws, strimmers, leaf blowers
- Some off-road and competition motorcycles
- Some outboard motors and personal watercraft
- Model engines and small mopeds in some markets
Two-stroke diesels and direct injection
Not all two-strokes work like a chainsaw:
- Large two-stroke marine diesels, which power many big cargo ships, use uniflow scavenging. A turbocharger or blower supplies the scavenging air, rather than the crankcase. They have a separate pressurised lubrication system, so no oil goes in the fuel. They are among the most efficient internal combustion engines built.
- Direct-injection two-strokes spray fuel straight into the cylinder after the exhaust port has closed, so short-circuiting loses only air, not fuel. This greatly reduces fuel waste and emissions, and has kept two-strokes in some modern outboards and off-road bikes.
For how two-strokes compare with car engines more broadly, see how a car engine works.