Engine Specs

Engine Efficiency: Thermal, Volumetric and Cycle Analysis

Thermal, mechanical and volumetric engine efficiency explained, with formulas, worked examples, BSFC, the Otto and Diesel cycles, and why no engine can reach 100%.

On this page
  1. Three different “efficiencies”
  2. Thermal efficiency
  3. Mechanical efficiency
  4. Volumetric efficiency
  5. Cycle analysis

Three different “efficiencies”

“Engine efficiency” can mean several different things, and the numbers aren’t interchangeable:

Term What it compares Typical meaning
Thermal efficiency Useful work out ÷ fuel energy in How well the engine converts fuel into work
Mechanical efficiency Brake (shaft) power ÷ indicated (in-cylinder) power How much is lost to friction and pumping
Volumetric efficiency Air actually drawn in ÷ air the displacement could hold How well the engine breathes

Thermal efficiency is the one that relates to fuel economy. Volumetric efficiency relates mostly to power potential and to fuel calibration.

Thermal efficiency

The basic formula

η_th = W_net ÷ Q_in = 1 − (Q_out ÷ Q_in)

W_net is the useful work produced, Q_in is the heat energy supplied by the fuel, and Q_out is the heat rejected to the exhaust, coolant and surroundings. Use consistent units (joules, kWh, Btu) and multiply by 100 for a percentage.

Engineers distinguish:

  • Indicated thermal efficiency, based on the work the gas does on the pistons.
  • Brake thermal efficiency (BTE), based on the power actually delivered at the crankshaft, after friction. This is the more practical figure.

Brake thermal efficiency from fuel use (BSFC)

Engine test data often gives brake specific fuel consumption (BSFC): grams of fuel burned per kilowatt-hour of brake output. If you know the fuel’s lower heating value (LHV) in MJ/kg:

BTE = 3,600 ÷ (BSFC in g/kWh × LHV in MJ/kg)

Gasoline’s LHV is roughly 43 MJ/kg and diesel’s roughly 42–43 MJ/kg. Exact values depend on the fuel blend.

Example: a gasoline engine at 250 g/kWh: BTE = 3,600 ÷ (250 × 43) ≈ 33.5%. A diesel at 200 g/kWh: BTE = 3,600 ÷ (200 × 42.6) ≈ 42%.

To work out brake power itself from dyno torque and rpm, see the brake power section of torque and horsepower explained.

Typical figures

These are approximate peak values. Efficiency varies across the operating range and is usually much lower at light load:

  • Modern gasoline car engines: peak brake thermal efficiency commonly in the mid-to-high 30s percent, with some recent designs, often in hybrids, reported at about 40%.
  • Diesel car and truck engines: usually higher than comparable gasoline engines, often in the 40s at best.
  • Large slow-speed marine diesels: among the most efficient piston engines, reported above 50%.
  • Formula 1 hybrid power units: manufacturers have reported thermal efficiencies above 50% for the combustion engine combined with energy recovery. These are highly specialized and the figures aren’t independently published in detail.

In everyday driving, a car engine spends much of its time at light load, where efficiency is well below its peak.

Can an engine be 100% efficient?

No. The second law of thermodynamics sets a ceiling for any heat engine working between a hot temperature T_H and a cold temperature T_C (both in kelvin). This ceiling is the Carnot efficiency:

η_Carnot = 1 − T_C ÷ T_H

Even an ideal engine must reject some heat to the cold side, so it can only reach 100% if the cold side were at absolute zero, which isn’t possible. Real engines fall well short of the Carnot limit because of heat loss to cylinder walls, friction, finite combustion speed, and exhaust that leaves while it’s still hot. “100% efficient” isn’t possible for any heat engine.

Mechanical efficiency

η_m = brake power ÷ indicated power

The difference, friction power, covers bearing and piston-ring friction, the valvetrain, oil and water pumps, and (depending on the convention used) the pumping work of drawing air in and pushing exhaust out.

Mechanical efficiency is highest at full load and falls at part load, because friction stays roughly the same while useful output drops. At idle with no load, brake power is zero, so mechanical efficiency is zero by definition. All the in-cylinder work goes into keeping the engine turning.

Volumetric efficiency

Volumetric efficiency (VE) compares how much air the engine actually takes in with the amount its displacement could theoretically hold. For an explanation of displacement itself, see engine capacity explained.

Strictly, VE should be a mass comparison, because air density changes with temperature and pressure. In practice it’s often expressed using volume flow measured at a reference condition.

Formula (imperial, CFM)

A four-stroke engine fills each cylinder once every two revolutions, so its theoretical airflow is CID × RPM ÷ 2 cubic inches per minute. Converting to cubic feet (1,728 in³ per ft³) gives the common formula:

VE (%) = CFM × 3,456 ÷ (CID × RPM) × 100

Example: a 350 cubic inch engine at 6,000 rpm could theoretically ingest 350 × 6,000 ÷ 3,456 ≈ 608 CFM. If it actually flows 520 CFM, VE ≈ 520 ÷ 608 ≈ 86%.

Formula (metric, MAF)

With a mass airflow (MAF) reading in grams per second:

VE = MAF ÷ (ρ × V_d × RPM ÷ 120)

ρ is air density in g/L (kg/m³), V_d is displacement in liters, and 120 covers both the minutes-to-seconds conversion and the two revolutions per intake event. Air density can be estimated as ρ = P ÷ (287 × T), with P in pascals and T in kelvin.

Example: a 2.0 L engine at 3,000 rpm, air density about 1.18 g/L. Theoretical flow = 1.18 × 2.0 × 3,000 ÷ 120 ≈ 59 g/s. A MAF reading of 50 g/s gives VE ≈ 85%.

Typical values, boost and idle

  • Naturally aspirated engines commonly run somewhere around 80–90% VE at wide-open throttle near their torque peak. Well-tuned performance engines can approach or slightly exceed 100% over a narrow rpm range, helped by intake and exhaust tuning.
  • Turbocharged and supercharged engines can show well over 100% when measured against outside air, because the compressor raises intake density. The engine isn’t breathing “better”. It’s being fed denser air.
  • At idle, a throttled gasoline engine’s VE measured against outside air is low, because the closed throttle holds manifold pressure well below atmospheric. Often it’s somewhere around a third of atmospheric, though this varies by engine. Diesels have no throttle, so their idle VE stays much higher. There’s no single “correct” idle VE. It depends on the engine and the reference used.

VE peaks roughly where torque peaks. Above that, breathing restrictions are one of the reasons torque falls off, and they influence where the redline ends up.

Cycle analysis

Engine cycle analysis models what happens to the gas inside the cylinder as a sequence of idealized processes. It’s usually shown on a pressure–volume (P–V) diagram. The simplest versions are air-standard cycles, which treat the working fluid as air with constant properties and replace combustion with heat addition.

Air-standard Otto cycle

The Otto cycle models a spark-ignition engine:

  1. Isentropic (ideal adiabatic) compression
  2. Heat addition at constant volume (combustion, idealized as instantaneous)
  3. Isentropic expansion (power stroke)
  4. Heat rejection at constant volume (exhaust)

Its efficiency depends only on the compression ratio r and the ratio of specific heats γ (about 1.4 for air):

η_Otto = 1 − 1 ÷ r^(γ − 1)

At r = 10, η ≈ 60%. At r = 12, η ≈ 63%. Gains shrink as r rises, which is part of why compression ratio is limited by knock long before efficiency stops improving.

Diesel and dual cycles

The Diesel cycle adds heat at constant pressure instead of constant volume, modeling fuel that burns as it’s injected. Its efficiency also depends on the cutoff ratio (how long heat addition lasts):

η_Diesel = 1 − (1 ÷ r^(γ−1)) × [(r_c^γ − 1) ÷ (γ × (r_c − 1))]

At the same compression ratio the Diesel cycle is less efficient than the Otto cycle. But diesel engines run much higher compression ratios, so in practice they usually come out ahead. The dual (limited-pressure) cycle combines constant-volume and constant-pressure heat addition and often matches real engines more closely.

Atkinson and Miller cycles

These cycles make the expansion stroke effectively longer than the compression stroke, extracting more work from the gas. Modern versions do this with valve timing, usually closing the intake valve late, rather than with special linkages. They trade some power density for efficiency and are common in hybrid vehicles.

Why real engines fall short

A real gasoline engine might reach a peak brake thermal efficiency of around 35–40%, compared with an ideal Otto figure of about 60%. The gap comes from:

  • Heat lost through the cylinder walls and head
  • Combustion that takes time rather than happening instantly at top dead center
  • Real gas properties (γ is lower than 1.4 for hot combustion gases)
  • Pumping losses, especially at part throttle
  • Friction and accessory loads
  • Exhaust valves opening before expansion is complete

Common thermodynamic cycles and “3-cycle” engines

Introductory courses usually focus on four idealized cycles: Carnot (the theoretical ideal), Otto (spark ignition), Diesel (compression ignition) and Brayton (gas turbines and jet engines). Stirling, Rankine (steam), Atkinson and Miller are also widely studied.

A car’s internal combustion engine is usually modeled with the Otto cycle (gasoline) or the Diesel or dual cycle (diesel). These operate mechanically as four-stroke or two-stroke engines. “Cycle” is often used loosely for “stroke”, as in “2-cycle oil”. There’s no common “3-cycle” engine type. Six-stroke and other variations have been proposed and experimented with, but they aren’t in mainstream use.

The complete guide to engine specs

Engine Specs Explained: How to Read Engine Names and Numbers
Read the guide

Keep exploring

Guides from other topics

All topics →