What engine oil does
An engine is full of metal parts moving against each other at high speed and under heavy load: crankshaft and bearings, pistons and cylinder walls, camshafts and valve gear. Without lubrication, they’d overheat, wear rapidly and seize. Engine oil does several jobs at once:
- Lubricates: Keeps a film between moving surfaces so they don’t touch.
- Cools: Carries heat away from bearings, pistons and other parts the coolant can’t reach directly.
- Cleans: Holds soot, combustion by-products and wear particles in suspension so the filter can catch them or they leave at the next oil change.
- Seals: Helps the piston rings seal against the cylinder wall.
- Protects: Additives in the oil help resist corrosion and deposits.
- Works hydraulically: In many modern engines, pressurised oil also operates hydraulic valve lifters, chain tensioners and variable valve timing.
For how these parts fit into the whole engine, see how a car engine works.
The oil’s journey through the engine
Most car engines use a pressurised, wet-sump system. Oil is stored in the sump at the bottom of the engine and pumped around a circuit.
Sump and pickup
The sump (oil pan) bolted under the engine holds the oil supply. A pickup tube, with a mesh screen on the end, dips into the oil near the lowest point and feeds the pump. The screen stops larger debris from reaching the pump.
Oil pump
The oil pump is driven mechanically by the engine: from the crankshaft, a camshaft, or a chain or shaft. So it pumps faster as revs rise. Common designs include:
- Gear pumps, which use two meshing gears
- Gerotor and rotor pumps, which use an inner and an outer rotor
- Variable-displacement vane pumps, which many modern engines use to deliver only as much oil as needed, cutting the power used to drive the pump
These are positive displacement pumps. Each turn moves a fixed volume of oil, so output climbs with engine speed.
Pressure relief valve
Because the pump’s output rises with revs, and cold oil is thick, pressure could climb too high. A spring-loaded pressure relief valve opens past a set pressure and sends the excess oil back to the sump or the pump inlet. That protects the filter, seals and pump.
Oil filter
Next, the oil passes through a full-flow oil filter, which traps fine particles. Most filters also contain:
- A bypass valve, which lets oil flow around the filter element if it becomes clogged or the oil is very cold and thick. Unfiltered oil is better than no oil.
- An anti-drainback valve in many designs, which stops the filter draining when the engine is off, so oil pressure builds faster at start-up.
Galleries and drillings
Filtered oil enters the main oil gallery, a passage running along the engine block. From there, smaller drillings branch off to:
- The main bearings, which support the crankshaft
- The connecting rod bearings, through passages drilled inside the crankshaft itself
- The camshaft bearings and valve train in the cylinder head
- The turbocharger, if fitted, where the shaft spins very fast and depends on a steady oil supply
- Hydraulic lifters, chain tensioners and variable valve timing units
Back to the sump
After passing through the bearings and other parts, oil drains back down to the sump under gravity, carrying heat and debris with it. Then the cycle repeats continuously while the engine runs.
How a bearing is lubricated: the oil wedge
The crankshaft doesn’t run on ball bearings. It turns in smooth plain bearings, also called shell bearings, with a very small clearance between the journal (the shaft) and the bearing shell.
When the shaft turns, it drags oil into the narrowing gap on the loaded side, forming a pressurised oil wedge that lifts the shaft slightly off the bearing surface. The shaft then floats on a thin film of oil, with no metal-to-metal contact. This is called hydrodynamic lubrication. The pump’s job is to keep that gap topped up with oil, so the film never runs dry.
The film is thinnest, and wear highest, at start-up, before oil pressure has fully built up, and when oil is too thin, too old or too low.
Parts that get oil without pressure: splash and jets
Not everything is fed by a drilled passage:
- Cylinder walls and pistons are mainly lubricated by oil thrown off the spinning crankshaft and connecting rods, and by oil escaping from the rod bearings. This is sometimes called splash lubrication.
- Many engines also have piston cooling jets, small nozzles that spray oil onto the underside of the pistons to cool them. They’re especially common in turbocharged and diesel engines.
- The piston rings spread oil on the cylinder wall and scrape most of it back down. The oil control ring is there to stop too much reaching the combustion chamber.
What creates oil pressure
The pump makes oil flow. Pressure comes from resistance to that flow, as oil squeezes through the tight bearing clearances and narrow passages. That has some useful consequences:
- Cold oil reads high. Thick oil resists flow, so pressure is higher until the engine warms up.
- Higher revs read higher, up to the point where the relief valve opens.
- Worn bearings read low. Larger clearances let oil escape more easily, so pressure drops. Low oil pressure on a worn engine, especially at hot idle, is a classic sign of bearing wear.
- Thin or diluted oil reads low. Oil that’s the wrong viscosity, or diluted with fuel, flows too easily.
Normal oil pressure
There’s no single “correct” number. It varies widely between engines and with temperature and revs. The manufacturer’s specification, found in the service information, is the reference. Pressure is typically lowest at hot idle and higher at cruising revs. Many cars have no gauge, only a warning light.
The oil pressure warning light
The red oil-can light usually comes on when a pressure switch detects that pressure has dropped very low. It’s not a gentle reminder. It’s a sign that the bearings may already be short of oil.
- It’s normal for it to light briefly when you switch the ignition on, and to go out within a second or two of starting.
- If it comes on while driving, stop safely as soon as possible and switch the engine off. Then check the oil level once the engine has had a few minutes to drain back. Running on with low oil pressure can wreck the engine in a short time.
- If the level is fine and the light still comes on, don’t drive the car until the cause has been found.
Some cars have a separate yellow or amber oil level warning or message. That’s a lower-priority alert to top up soon.
Oil level vs oil pressure
These aren’t the same thing, and it’s a common confusion:
- Oil level is how much oil is in the sump. Check it with the dipstick or the car’s electronic level reading, with the car on level ground.
- Oil pressure is how hard the oil is being pushed through the engine.
If the level falls low enough, the pickup can start sucking air, especially on corners or hills, and pressure collapses. But pressure can also be lost with a full sump, for example from a failed pump, a blocked pickup screen or badly worn bearings. Checking the level regularly is still one of the simplest ways to protect an engine.
Wet sump vs dry sump
- Wet sump: The oil sits in the pan under the engine, and the pump draws from it. It’s simple, cheap and used in almost all road cars.
- Dry sump: Scavenge pumps pull oil out of a shallow pan into a separate tank, and a pressure pump feeds the engine from there. It’s used in racing cars, some high-performance road cars and aircraft. It keeps the supply steady under hard cornering and lets the engine sit lower in the car.
Two-stroke engines usually use a completely different approach, with the oil mixed into the fuel. See how a two-stroke engine works.
Viscosity: what 5W-30 means
Viscosity is how thick the oil is, meaning its resistance to flow. Multigrade oils carry two numbers:
- The number before the W (for winter), such as 5 in 5W-30, describes how the oil behaves when cold. A lower number flows more readily at low temperatures, which matters at start-up.
- The number after it, 30, describes its viscosity at normal operating temperature.
Use the viscosity grade and specification your engine’s manufacturer lists. Modern engines with tight clearances, hydraulic valve timing and turbochargers are designed around a particular oil, and the wrong one can affect oil pressure and protection.
How lubrication systems fail
Lubrication problems are among the most destructive engine faults:
- Low oil level from leaks, burning oil or missed top-ups, leading to oil starvation
- Overdue oil changes, letting oil break down and form sludge that can block the pickup screen and drillings
- Clogged or cheap filters that bypass or restrict flow
- Worn bearings, which lower pressure and allow further wear
- Pump or pickup failure, or a blocked screen
- Overheating, which thins and degrades oil. That’s one reason the cooling system matters for lubrication too.
The basics prevent most of this: check the level regularly, change the oil and filter at the intervals the manufacturer recommends, and never ignore the red oil light.