Timing and Valvetrain

Engine Firing Order Explained: Why 1-3-4-2 and How to Find Yours

What engine firing order is, why most four-cylinder engines fire 1-3-4-2, common firing orders for other engines, and how to find your engine's order.

On this page
  1. What firing order means
  2. Why firing order matters
  3. Why most four-cylinder engines fire 1-3-4-2
  4. Common firing orders
  5. Cylinder numbering
  6. How to find your engine’s firing order
  7. What happens if the firing order is wrong
  8. Firing order vs ignition timing
  9. Firing order in modern coil-on-plug and diesel engines

What firing order means

An engine’s firing order is the sequence in which its cylinders produce their power strokes. In a gasoline engine, it’s the order in which the spark plugs fire. In a diesel, it’s the order in which fuel is injected, since diesels ignite fuel by compression rather than spark.

Firing order is written as a list of cylinder numbers. A firing order of 1-3-4-2 means cylinder 1 fires first, then 3, then 4, then 2, and the pattern repeats.

In a four-stroke engine, each cylinder fires once every two crankshaft revolutions (720 degrees). With evenly spaced firing, the gap between power strokes is 720 divided by the number of cylinders: 180 degrees in a four-cylinder, 120 degrees in a six and 90 degrees in a V8. Some engines, such as many V-twins and certain V6 and V10 designs, have uneven intervals by design.

Why firing order matters

The firing order is decided when the engine is designed, and it’s tied to the shape of the crankshaft and the camshaft lobes. You can’t change it by rearranging plug wires. Engineers choose it to balance several factors.

Smoothness and crankshaft loads

Each power stroke twists the crankshaft and loads the main bearings nearest that cylinder. Spreading the power strokes along the length of the engine, rather than firing neighboring cylinders one after another, helps:

  • Reduce vibration and twisting (torsional) stress on the crankshaft
  • Share the load between main bearings
  • Avoid concentrating heat at one end of the engine

Exhaust flow and sound

Firing order also determines the order in which exhaust pulses arrive in the exhaust manifold. Exhaust designers try to avoid one cylinder’s pulse interfering with another’s when they share a manifold branch. On V engines, the firing order decides how pulses alternate between the two banks, which is a big part of why different engines sound the way they do. The classic uneven burble of a traditional cross-plane V8 comes partly from each bank’s exhaust receiving pulses at uneven intervals.

Why most four-cylinder engines fire 1-3-4-2

Most inline four-cylinder engines have a flat crankshaft in which cylinders 1 and 4 rise and fall together, and cylinders 2 and 3 rise and fall together, 180 degrees apart from the first pair. That layout is good for primary balance.

When cylinders 1 and 4 both reach top dead center, one is at the end of its compression stroke and the other is at the end of its exhaust stroke. Say cylinder 1 fires. Half a turn later, cylinders 2 and 3 reach the top together, and one of them is on compression. The designer chooses which, and that choice is set by the camshaft:

  • If it’s cylinder 3, the order becomes 1-3-4-2.
  • If it’s cylinder 2, the order becomes 1-2-4-3.

Both orders give the same even 180-degree spacing. 1-3-4-2 is the more common choice, and 1-2-4-3 is used on some engines. A sequence such as 1-2-3-4 isn’t possible with this crankshaft layout, because the two cylinders in a pair (1 and 4, or 2 and 3) always fire a full revolution apart, so they can never fire one straight after the other.

This pairing is also why wasted-spark ignition systems on four-cylinder engines typically pair cylinders 1 and 4 on one coil and 2 and 3 on another. See how a gasoline engine ignition system works for more on that.

Common firing orders

Firing orders vary by engine, so always confirm yours. These are widely used examples:

Engine type Common firing order
Inline-4 1-3-4-2 (sometimes 1-2-4-3)
Inline-5 1-2-4-5-3
Inline-6 1-5-3-6-2-4
Flat-4 (air-cooled Volkswagen) 1-4-3-2
Flat-4 (many Subaru engines) 1-3-2-4
Traditional GM small-block and big-block V8 1-8-4-3-6-5-7-2
GM LS-family V8 1-8-7-2-6-5-4-3
Ford 289/302 V8 (most) 1-5-4-2-6-3-7-8
Ford 351W and 5.0 H.O. V8 1-3-7-2-6-5-4-8

The numbers only make sense alongside the manufacturer’s cylinder numbering, which is the next point.

Cylinder numbering

Firing order lists cylinder numbers, but manufacturers don’t all number cylinders the same way.

  • Inline engines are usually numbered from the front, the timing belt or chain end, to the rear (the transmission end). On a transverse engine, the “front” is still the timing end, which may be on the side of the car.
  • V engines vary. Many GM V8s number odd cylinders (1-3-5-7) on the driver’s side and even cylinders (2-4-6-8) on the passenger side. Many Ford V8s number 1 to 4 down the passenger side and 5 to 8 down the driver’s side (in left-hand-drive markets).
  • Flat engines vary by manufacturer.

So two engines can fire their cylinders in the same physical pattern but write it as different numbers. Always find the numbering diagram for your engine before using a firing order.

How to find your engine’s firing order

Good sources, roughly in order of reliability:

  1. The service or repair manual for your exact engine, which will show both the firing order and a cylinder numbering diagram.
  2. Markings on the engine. Some engines have the firing order cast or stamped into the intake manifold or printed on a label under the hood. Cylinder numbers are sometimes marked on the manifold or the distributor cap.
  3. The distributor cap. On older engines, the cylinder 1 terminal is often marked. Following the direction the rotor turns from there gives the firing order around the cap.
  4. Parts catalogs and manufacturer data, looked up by engine code, not just model name.

On a distributor engine, the direction the rotor turns matters. Crank the engine briefly with the cap off, or check the manual, before routing wires around the cap.

What happens if the firing order is wrong

The engine’s mechanical firing order can’t be wrong unless parts are installed incorrectly. But the ignition can be connected in the wrong sequence, most commonly by mixing up plug wires or coil connectors. Symptoms of wires in the wrong order include:

  • Misfiring and rough running
  • Popping or backfiring through the intake or exhaust
  • Loss of power
  • Hard starting, or no start if several wires are wrong
  • A check engine light with misfire codes on modern cars

Two wires swapped on neighboring cylinders that fire one after the other is a classic mistake, particularly on V8s with two cylinders physically close together. Replacing plug wires one at a time, so each new wire goes exactly where the old one was, avoids most problems.

Firing order vs ignition timing

These two are often confused:

  • Firing order is which cylinder fires next.
  • Ignition timing is when, in degrees of crankshaft rotation, each cylinder’s spark happens relative to top dead center.

An engine can have the correct firing order and wrong timing, or the reverse. Our engine timing guide explains ignition timing, valve timing and how they’re set.

Firing order in modern coil-on-plug and diesel engines

On engines with coil-on-plug ignition, the engine computer fires each coil in the correct order, so there are no plug wires to mix up. The coil connectors themselves can still be swapped by mistake on some engines, so it’s worth labeling them during repairs.

Diesel engines follow a firing order too, set by the injection system. On older diesels with mechanical injection pumps, the injector lines must be connected in the correct order; on common-rail diesels, the engine computer controls injection timing and sequence.

Whatever the engine, the firing order works together with the valve timing. The camshaft has to open the right valves for each cylinder at the right moment, which is why the timing belt or chain is so critical to keep in good condition.

The complete guide to timing and valvetrain

Engine Timing Explained: Ignition Timing, Valve Timing and Timing Wheels
Read the guide

Keep exploring

Guides from other topics

All topics →