What the ignition system does
A gasoline engine compresses a mixture of air and fuel, but compression alone isn’t meant to ignite it. Something has to light it, and in a gasoline engine that’s an electric spark jumping across the gap of a spark plug. The ignition system’s job is to:
- Turn the car’s low-voltage electrical supply into a voltage high enough to jump the plug gap under compression, typically tens of thousands of volts.
- Deliver that spark to the right cylinder.
- Fire it at the right moment in the piston’s travel, adjusting that moment as speed and load change.
The third job, ignition timing, is covered in more depth in our engine timing guide. This article focuses on the hardware and how it has changed from mechanical points to modern coil-on-plug systems.
The main components
When people ask about the “five major components” of an ignition system, a conventional older system is usually described as:
- Battery (and, once the engine is running, the alternator), which supplies low-voltage power
- Ignition switch, which turns the system on
- Ignition coil, which steps the voltage up
- Distributor, which contains the points, the advance mechanisms and the rotor that routes the spark to each cylinder
- Spark plugs and plug wires, which deliver the spark into the combustion chamber
The condenser, distributor cap and rotor are usually counted as parts of the distributor. Modern systems replace the points and distributor with sensors, an engine computer and individual coils, but the battery, coil and spark plug are still there.
How the coil turns 12 volts into a spark
An ignition coil is a type of transformer. Inside are two windings around an iron core:
- The primary winding: relatively few turns of heavier wire, connected to the 12-volt supply.
- The secondary winding: many thousands of turns of very fine wire, connected to the spark plug.
When current flows through the primary winding, it builds a magnetic field in the core. When that current is suddenly switched off, the field collapses rapidly. The collapsing field induces a voltage in both windings, and because the secondary has so many more turns, the voltage it produces is far higher. That high-voltage pulse is what jumps the plug gap.
The key point is that the spark happens when primary current is switched off, not when it is switched on. Everything else in the system, from points to engine computers, exists to switch that primary current at exactly the right moment.
Primary and secondary circuits
Ignition systems are often described in two halves:
- Primary (low-tension) circuit: battery, ignition switch, coil primary winding, and whatever switches the current (points or an electronic module).
- Secondary (high-tension) circuit: coil secondary winding, coil lead, distributor cap and rotor (if fitted), plug wires and spark plugs.
Contact breaker points and the condenser
For most of the 20th century, the switch in the primary circuit was a set of contact breaker points, usually just called “points”. This is what people mean by “points in a car engine”.
The points are a pair of small metal contacts inside the distributor. One is fixed; the other sits on a spring-loaded arm with a rubbing block that rides on a cam in the center of the distributor shaft. The cam has one lobe per cylinder. As the shaft turns, each lobe pushes the points open, interrupting the primary current and firing the coil. When the lobe passes, the spring closes the points and the coil starts charging again.
Wired across the points is a condenser (a capacitor). Without it, the coil’s stored energy would arc across the points as they opened, burning them quickly and weakening the spark. The condenser absorbs that surge, which lets the primary current stop more cleanly and helps the coil produce a strong secondary pulse.
Dwell and point gap
Two adjustments matter on a points system:
- Point gap: how far the points open at the top of the cam lobe, set with a feeler gauge.
- Dwell: how many degrees of distributor rotation the points stay closed, measured with a dwell meter.
Gap and dwell are linked. A smaller gap means the points stay closed longer (more dwell), and a larger gap means less dwell. Dwell matters because the coil needs time with current flowing to build a full magnetic field. Changing the gap also shifts ignition timing slightly, so timing is normally checked after the points are adjusted.
As the rubbing block wears, the gap closes up and the dwell and timing drift. This is why points needed regular inspection and adjustment, and periodic replacement.
How to tell if your points are bad
Common signs of worn or misadjusted points include:
- Hard starting, especially when the engine is warm or the battery is weak
- Misfiring or stumbling, often worse at higher RPM
- Rough idle
- Gradual loss of power and fuel economy
- Ignition timing that won’t stay where you set it
On inspection, the contact faces may be pitted, burned, blued or built up with a small crater on one side and a peak on the other. A worn rubbing block or a dwell reading well outside the specification also points to the need for adjustment or new points. Heavy pitting can also suggest a failing condenser, which is why points and condenser were usually replaced together.
The distributor and timing advance
On older engines, the distributor is driven by the camshaft at half crankshaft speed. It does two things:
- Times the spark: the points (or a pickup on later systems) open at the right moment for each cylinder.
- Distributes the spark: a spinning rotor under the distributor cap passes each plug wire terminal in turn, routing the coil’s high-voltage pulse in the engine’s firing order. Our firing order explainer covers why cylinders fire in the sequence they do.
Most distributors also adjust timing as the engine runs:
- Centrifugal (mechanical) advance: weights on the distributor shaft fly outward as RPM rises, rotating the cam to fire the spark earlier.
- Vacuum advance: a diaphragm connected to engine vacuum moves the points’ mounting plate to add advance at light load.
Base timing is set by rotating the whole distributor body.
Electronic ignition replaces the points
Points have built-in limits. They wear, they drift out of adjustment, and at high RPM the arm can “float” and fail to follow the cam. They also limit how much current can be switched through the coil.
Electronic (breakerless) ignition kept the distributor but replaced the points with a non-contact sensor, usually a magnetic pickup or Hall-effect sensor, and an electronic ignition module that switches the coil. Benefits included:
- No rubbing parts to wear, so dwell and timing stay put
- A stronger, more consistent spark
- Much longer service intervals
When did cars stop using points?
There’s no single year. In the United States, the major manufacturers moved most of their cars to electronic ignition during the mid-1970s, helped along by emissions rules that favored ignition systems that stayed in adjustment. Some imported cars, small engines and motorcycles kept points for longer, in some cases into the 1980s. Many owners of classic cars have since fitted electronic conversion kits inside their original distributors.
Distributorless and wasted-spark ignition
The next step removed the distributor entirely. In a distributorless ignition system, the engine computer works out crankshaft position from a crankshaft position sensor (and often a camshaft sensor) and fires coils directly.
A common early version is wasted spark. Each coil serves two cylinders whose pistons reach the top at the same time, one on its compression stroke and one on its exhaust stroke. The coil fires both plugs at once. The spark in the compression cylinder ignites the mixture; the one in the exhaust cylinder does nothing useful, hence “wasted”. On a typical four-cylinder engine, cylinders 1 and 4 share one coil and 2 and 3 share another.
Coil-on-plug ignition
Most modern gasoline engines use coil-on-plug (COP) ignition: a small individual coil sits directly on top of each spark plug, with no plug wires. The engine computer controls each coil separately.
Advantages include:
- No long high-voltage leads to break down or leak energy
- Precise, cylinder-by-cylinder timing control
- The ability to retard timing on a single cylinder when the knock sensor detects knock
- Easier diagnosis, since a misfire can often be traced to one coil
The trade-off is that a failing coil is now a part in its own right. Swapping a suspect coil to another cylinder and seeing whether the misfire moves with it is a common diagnostic step.
Ignition vs fuel system
The ignition and fuel systems work together but do different jobs. The fuel system (carburetor or fuel injectors) delivers fuel in the right amount; the ignition system provides the spark that lights it. A strong spark can’t fix a lean or flooded mixture, and perfect fuel delivery is useless with no spark. On a modern engine one computer controls both, which is why one sensor failure, such as a crankshaft position sensor, can stop both spark and injection at once.
Diesel engines don’t use an ignition system of this kind at all. They rely on the heat of compression to ignite the fuel as it’s injected.
Common ignition problems and how they are tested
Typical ignition faults include:
- Worn, fouled or incorrectly gapped spark plugs
- Failing coils or coil packs
- Cracked or leaking plug wires
- A cracked distributor cap or worn rotor (older systems)
- Worn points or a failed condenser (points systems)
- A failed ignition module or crankshaft position sensor
- Poor battery voltage or bad ground connections
A logical test sequence usually starts simple: check battery voltage and connections, scan for fault codes on modern cars, inspect the spark plugs, and confirm spark with an inline spark tester. If there’s no spark, the next steps are checking power and ground to the coil or module, then the crankshaft sensor signal. Coil primary and secondary resistance can be checked with a multimeter against the manufacturer’s specifications. Misfires that move when a coil is swapped point to the coil; misfires that stay in the same cylinder point elsewhere, such as the plug, injector or compression.
Many misfire symptoms can also come from fuel delivery, vacuum leaks or low compression, so it’s worth confirming the ignition system is at fault before replacing parts.
A safety note on high voltage
Ignition secondary voltage can give a painful and dangerous shock. Don’t hold plug wires, coils or plug terminals while the engine is cranking or running, and use an insulated spark tester rather than holding a plug against the engine. Take particular care if you have a heart condition or medical implant. Follow the vehicle manufacturer’s service procedure, and if you’re not comfortable working around the system, leave testing to a professional.