Engine Problems

Engine Misfire: Causes, Codes and How to Find the Bad Cylinder

What causes an engine misfire, what P0300 to P0308 codes mean, and how to find the misfiring cylinder with coil swaps, plug checks and compression tests.

On this page
  1. What an engine misfire is
  2. Symptoms of a misfire
  3. How the engine computer detects a misfire
  4. Misfire codes explained
  5. Engine misfire causes
  6. Reading the misfire pattern
  7. How to find the bad cylinder
  8. Misfire without a code
  9. Is it safe to drive with a misfire?

A misfire happens when one or more cylinders fail to burn their air-fuel mixture properly. You might feel it as a stumble, a shake at idle or a jerk under acceleration. The engine computer often stores a code that names the cylinder. That code is where diagnosis starts, not where it ends. This guide covers the causes, the codes, and practical ways to confirm which part is to blame.

What an engine misfire is

For a cylinder to fire properly, it needs:

  1. The right amount of air and fuel
  2. A strong spark at the right moment (gasoline engines)
  3. Enough compression to make the mixture burn effectively
  4. Correct timing of the valves and ignition

If any of these is missing or weak in a cylinder, combustion is weak, partial or absent. That cylinder stops contributing its share of power, and the engine runs unevenly. A misfire can be constant, intermittent, limited to one cylinder, or spread randomly across several.

Symptoms of a misfire

  • Rough or shaking idle
  • Hesitation, stumbling or jerking when accelerating, especially under load or uphill
  • Loss of power
  • An uneven or “popping” exhaust note
  • Check engine light, steady or flashing
  • Poorer fuel economy, and sometimes a smell of raw fuel
  • Hard starting or stalling in severe cases

How the engine computer detects a misfire

Most OBD-II systems detect misfires by watching crankshaft speed. Each time a cylinder fires, it gives the crankshaft a small push. If a cylinder misfires, the crankshaft slows very slightly at that point in its rotation. The computer compares these tiny speed changes. If misfires exceed certain thresholds, it sets a code. If they’re severe enough to risk catalytic converter damage, it flashes the check engine light.

This is why rough roads, unbalanced tires or driveline problems can occasionally cause false misfire detection on some vehicles. It’s also why a light misfire may not set a code at all.

Misfire codes explained

Code Meaning
P0300 Random or multiple cylinder misfire detected
P0301 Cylinder 1 misfire detected
P0302 Cylinder 2 misfire detected
P0303 to P0308 Cylinders 3 to 8 misfire detected (P0309 to P0312 exist for engines with more cylinders)

Cylinder numbering varies by manufacturer and engine layout. Check the service information for your engine before assuming which cylinder is “number 1.”

A cylinder-specific code says where the misfire is. It doesn’t say why. A P0302 could be a bad coil, plug, injector, a vacuum leak near that cylinder, a leaking valve or a wiring fault. P0300 often points toward something shared by all cylinders, such as fuel pressure, a large vacuum leak, a sensor or timing.

Other codes stored alongside a misfire can be very helpful: lean codes (P0171/P0174), coil circuit codes, injector circuit codes, or cam and crank correlation codes.

Engine misfire causes

Ignition

  • Worn or fouled spark plugs: a worn electrode or a widened gap needs more voltage to spark, especially under load
  • A failing ignition coil (coil-on-plug or coil pack): often worse when hot or under acceleration
  • Damaged plug wires or coil boots: cracks, carbon tracking or moisture let the spark leak to ground
  • Distributor cap and rotor problems on older engines
  • Wiring and connector faults in the coil circuit

Fuel

  • A clogged or sticking injector: too little fuel, so that cylinder runs lean
  • A leaking injector: too much fuel, which can flood the cylinder, especially after the engine sits
  • Low fuel pressure: a weak pump, clogged filter or faulty regulator. Usually affects several cylinders under load.
  • Contaminated fuel
  • Injector circuit or driver faults

Air and vacuum leaks

  • Vacuum leaks at the intake gasket, hoses or PCV system lean out the mixture. A leak near one runner can cause misfires in a single cylinder.
  • A dirty or faulty MAF sensor causes incorrect fueling across all cylinders.
  • EGR faults: too much exhaust gas recirculation at the wrong time dilutes the mixture.

Compression and mechanical faults

  • A burned or sticking valve
  • Worn piston rings or a damaged piston
  • A head gasket leak between cylinders or into a coolant passage. See blown head gasket symptoms.
  • Worn camshaft lobes or faulty lifters or rockers
  • Carbon buildup on intake valves, a known issue on some direct-injection engines

Timing and sensors

Reading the misfire pattern

Pattern Common directions to investigate
Same cylinder every time Coil, plug, injector, wiring for that cylinder; local vacuum leak; low compression
Random or multiple cylinders Fuel pressure, vacuum leak, MAF sensor, EGR, timing, fuel quality
Mostly at idle Vacuum leak, injector, EGR, low compression
Mostly under acceleration or load Worn plugs, weak coil, low fuel pressure
Worse on cold start Leaking injector, ignition moisture, low compression, possible coolant entering a cylinder
Starts after warm-up Heat-sensitive coil or wiring, sensor, fuel issue
In wet weather Cracked coil boot, plug wire or water in the plug well

How to find the bad cylinder

Safety: ignition systems produce high voltages. Don’t pull plug wires or coils off a running engine to “find” a misfire. It risks a shock, can damage the ignition system and stresses the catalytic converter. Work with the engine off and cool, and disconnect power to coils or injectors as the service procedure describes.

Swap the coil

On engines with individual coils, swap the coil from the misfiring cylinder with one from a neighboring cylinder. Clear the codes and drive under similar conditions.

  • If the misfire moves to the other cylinder (for example, P0302 becomes P0303), the coil is faulty.
  • If it stays put, the coil isn’t the problem.

Many scanners can also show live misfire counts per cylinder, or “Mode 6” test results. These let you confirm a change without waiting for a code.

Inspect and swap the spark plug

Remove the plug and compare it with the others:

  • Oily, wet deposits: oil entering the cylinder
  • Heavy black soot: rich running
  • White, blistered deposits: very lean running or overheating
  • Cracked insulator or damaged electrode: replace the plug

A suspect plug can also be swapped to another cylinder to see whether the misfire follows it. In practice, if plugs are due, replacing the full set is usually sensible.

Check the injector

Listen to each injector with a mechanic’s stethoscope or a long screwdriver held carefully against the body. A healthy injector clicks steadily. A noid light can confirm that the injector is receiving a signal. On port-injected engines, swapping injectors between cylinders works the same way as a coil swap, though it’s more work. Direct-injection systems run at very high fuel pressures and are best left to professionals.

Test compression

If spark and fuel check out, test compression. Look for a cylinder that reads well below the others. A leak-down test then shows where the pressure is escaping: past the rings, past the valves or through the head gasket. Our guide to worn engine symptoms explains how to interpret these tests.

Misfire without a code

A mild or intermittent misfire may not cross the threshold for a code. If you can feel a stumble but there’s no code:

  • Check for pending codes, and look at misfire counters in live data if your scanner supports them.
  • Inspect plugs and coil boots anyway.
  • Consider issues that feel like misfires but aren’t: worn engine mounts, torque converter shudder, or a fuel delivery problem under load. See our guide to idle and RPM problems.

Is it safe to drive with a misfire?

  • Flashing check engine light: reduce load and stop driving as soon as it’s safe. A severe misfire sends unburned fuel into the exhaust, where it can overheat and damage the catalytic converter. Arrange a repair or tow.
  • Steady light with a mild misfire: usually OK to drive gently to a repair, but don’t delay. Misfires waste fuel and can damage the converter over time.
  • With fuel smell, heavy shaking or overheating: stop and get help.

For the overall troubleshooting method, see how to diagnose engine problems. If you’re reading codes yourself, doing a car diagnostic yourself explains freeze frames and live data.

The complete guide to engine problems

How to Diagnose Engine Problems: Symptoms, Causes and Fixes
Read the guide

Keep exploring

Guides from other topics

All topics →