Engine Specs

Engine Specs Explained: How to Read Engine Names and Numbers

Learn to read an engine spec sheet: displacement, cylinder layout, DOHC and 16V, turbo, hp vs bhp vs PS, torque, compression ratio and engine codes.

On this page
  1. Reading a spec line: a worked example
  2. Displacement: the engine’s size
  3. Cylinder count and layout
  4. Valvetrain: OHV, SOHC, DOHC and valve count
  5. Aspiration and fuel delivery
  6. Power and torque figures
  7. Bore, stroke and compression ratio
  8. Redline
  9. Engine codes and nomenclature
  10. How to tell what engine your car has
  11. Quick answers to common questions
  12. Where to go next

Reading a spec line: a worked example

Car brochures, owner’s manuals and review sites usually boil an engine down to one dense line. Here’s an illustrative one, typical of a modern turbocharged four-cylinder:

2.0 L turbocharged DOHC 16-valve inline-four, direct injection — 250 hp @ 5,500 rpm, 273 lb-ft @ 1,800–4,500 rpm — bore × stroke 86 × 86 mm — compression ratio 9.5:1 — redline 6,500 rpm

Each part of that line answers a different question about the engine:

Spec What it tells you
2.0 L Displacement: how much air the cylinders sweep through
Turbocharged Aspiration: whether air is forced in or drawn in by the pistons alone
DOHC 16-valve Valvetrain: where the camshafts are and how many valves there are
Inline-four Cylinder count and how they’re arranged
Direct injection How fuel gets into the cylinder
250 hp @ 5,500 rpm Peak power and the engine speed where it occurs
273 lb-ft @ 1,800–4,500 rpm Peak torque and the speed range where it’s available
86 × 86 mm Cylinder diameter and piston travel
9.5:1 How tightly the mixture is squeezed
6,500 rpm The highest speed the engine is meant to run at

The rest of this guide goes through each item, then covers engine codes and how to work out which engine your own vehicle has.

Displacement: the engine’s size

Displacement (also called engine capacity or engine size) is the total volume the pistons sweep as they travel from the bottom of their stroke to the top, added up across every cylinder. It’s quoted in cubic centimeters (cc), liters (L) or, especially on older American engines, cubic inches (ci or CID). 1,000 cc equals 1 liter, and 1 liter is about 61 cubic inches.

Displacement is a rough guide to an engine’s potential, since a bigger engine can process more air and fuel per revolution. Turbocharging has weakened that link a lot, though: a modern 2.0 L turbo can outperform an older naturally aspirated 3.5 L. The badge figure is also usually rounded. For the formula, conversions and what the number does and doesn’t tell you, see our full guide to engine capacity and displacement.

Rounding is why the same engine can show up under two names. A classic Chevrolet “350” and a “5.7 L” are the same displacement in different units, but not every 5.7 L engine is a 350. We untangle that in Is a 5.7 L engine the same as a 350?

Cylinder count and layout

The letter-and-number code describes how many cylinders there are and how they’re arranged:

  • I4, I6 (or L4, L6, “straight”): inline, with all the cylinders in one row. Inline-fours are the most common car engine layout worldwide, and inline-sixes are known for smoothness.
  • V6, V8, V12: two banks of cylinders set at an angle to each other, sharing one crankshaft. A V layout makes a many-cylinder engine shorter.
  • H4, H6 (flat, “boxer”): two banks lying flat, 180° apart, with opposing pistons moving in and out together. Subaru and Porsche are well-known users. Many light-aircraft engines are also horizontally opposed, which is where the “O” in names like the Lycoming O-320 comes from.
  • I3: inline-three, now common in small turbocharged cars.
  • VR6, W12, W16: specialized compact layouts used mainly by the Volkswagen group.

More cylinders usually means smoother running and higher potential output, at the cost of size, weight, friction and complexity.

Valvetrain: OHV, SOHC, DOHC and valve count

These abbreviations describe where the camshafts sit and how they operate the valves:

  • OHV (overhead valve, “pushrod”): a single camshaft in the block operates the valves through pushrods and rocker arms. It makes for a compact engine, and the classic American V8s are the best-known examples.
  • SOHC (single overhead cam): one camshaft per cylinder head, sitting above the valves.
  • DOHC (double overhead cam, “twin cam”): two camshafts per cylinder head, one for the intake valves and one for the exhaust. Most modern car engines are DOHC.

A figure like 16V or 24V is the total valve count. A 16-valve four-cylinder has four valves per cylinder (two intake, two exhaust), which generally helps the engine breathe at higher rpm. You’ll also see variable valve timing named by brand: VTEC (Honda), VVT-i (Toyota), VANOS (BMW) and others.

Aspiration and fuel delivery

  • Naturally aspirated (NA): the pistons draw air in using atmospheric pressure alone.
  • Turbocharged: an exhaust-driven turbine spins a compressor that pushes extra air in.
  • Supercharged: the compressor is driven mechanically, usually by a belt from the crankshaft.

For fuel delivery, you’ll see carbureted (older engines), port or multi-point injection (MPI/PFI, which sprays fuel into the intake ports), and direct injection (DI, GDI, TSI, which sprays fuel straight into the cylinder). Some engines use both port and direct injection. Diesel spec sheets usually mention common rail, a high-pressure direct injection system.

Power and torque figures

Torque is the twisting force the engine produces at the crankshaft. Power is how quickly that force does work, which means torque multiplied by engine speed. That’s why both figures come with an rpm attached. Our article on torque and horsepower covers the formulas, units and how to read a power curve in depth.

hp, bhp, PS and kW

  • hp: in the US this usually means mechanical horsepower, about 745.7 watts.
  • bhp (brake horsepower): power measured at the crankshaft on a dynamometer (historically a “brake”), before losses in the gearbox and driveline. In everyday use, bhp and hp are often the same figure. The “brake” part just says where it was measured.
  • PS (or CV, ch): metric horsepower, about 735.5 watts, so slightly smaller than a mechanical horsepower. 100 PS is about 98.6 hp.
  • kW: the SI unit, used on official documents in many countries. 1 kW is about 1.34 hp or 1.36 PS.

Older American figures can be confusing because they changed basis. Before the early 1970s, US manufacturers commonly quoted SAE “gross” power, measured without some accessories and exhaust restrictions. Later “net” ratings are measured more like the engine is installed, so they tend to look lower for the same engine.

Figures measured at the wheels (wheel horsepower, whp) are lower than crank figures because the transmission and driveline absorb some power.

Why the rpm matters

“273 lb-ft @ 1,800–4,500 rpm” tells you the engine delivers its peak torque across a broad band. That’s typical of turbocharged engines and makes a car feel strong in everyday driving. A naturally aspirated engine might make similar peak power but only near the top of its rev range. Two engines with the same peak numbers can feel very different on the road. If you’re comparing torque figures for a daily driver, our answer to whether 200 Nm of torque is good for a car shows how vehicle weight and gearing change the picture.

Bore, stroke and compression ratio

Bore × stroke gives the cylinder diameter and the distance the piston travels, usually in millimeters. An engine with a bore bigger than its stroke is “oversquare” and one with a longer stroke is “undersquare”. The ratio says something about the engine’s character and rev potential. See bore and stroke: oversquare vs undersquare engines.

Compression ratio (for example 9.5:1 or 13:1) compares the cylinder’s volume with the piston at the bottom to its volume with the piston at the top. Higher ratios generally improve efficiency but raise the risk of knock, which ties compression ratio to fuel octane. Diesels use much higher ratios than gasoline engines. Our compression ratio explainer shows how to calculate it and what typical figures mean.

Both feed into how efficiently an engine turns fuel into work, which we cover in engine efficiency: thermal, volumetric and cycle analysis.

Redline

Redline is the maximum engine speed the manufacturer intends the engine to run at, shown as a red zone on the tachometer and usually enforced by an electronic rev limiter. It’s set by whichever part reaches its limit first: the valvetrain, the connecting rods, piston speed and so on. That’s why a big diesel might redline below 5,000 rpm while some sports-car engines rev past 8,000. See what determines an engine’s redline.

Engine codes and nomenclature

Manufacturer codes

Most manufacturers give each engine family an internal code, and enthusiasts often use these instead of displacement. A few examples:

  • GM: small-block V8s are often known by RPO codes such as L98, LT1 or LS1.
  • Honda: codes like K20A or B16A combine a family letter, a displacement figure in deciliters (20 = 2.0 L) and a variant letter.
  • Toyota: in a code like 2JZ-GTE, “2” is the variant within the JZ family, “JZ” is the family, and the letters after the dash describe features. G is a performance-oriented DOHC head, T is turbocharged and E is electronic fuel injection.
  • Volkswagen group: family names like EA888, with separate short engine codes stamped on each unit.

These schemes aren’t standardized between brands, and manufacturers sometimes change their own conventions. Treat any decoding guide as a starting point and check the manufacturer’s documentation for a specific engine.

Marketing names

Names like EcoBoost, HEMI, Vortec, SkyActiv or TSI are brand names for a family or technology, not precise specifications. The same marketing name can cover very different engines across sizes and years.

Aircraft engine names

Piston aircraft engines follow a more systematic scheme. In the US, Lycoming and Continental names combine letters for configuration with the displacement in cubic inches. An IO-360 is a fuel-injected, horizontally opposed engine of about 360 cubic inches. See what the O means in Lycoming O-320 for the full set of prefixes.

How to tell what engine your car has

There are several reliable places to check:

  1. The owner’s manual or original sales documents usually list the engine size and type.
  2. The underhood emissions label. Many vehicles carry a sticker under the hood listing the engine family and displacement.
  3. The VIN (vehicle identification number). On many vehicles sold in North America, one character (commonly the 8th) encodes the engine. The scheme varies by manufacturer, so decode it with the manufacturer’s information or a reputable VIN decoder.
  4. Registration or title documents, which in many countries record engine capacity in cc.
  5. The engine itself. The engine cover may show the displacement, and the block carries a stamped engine number.

An engine serial number (engine number) is different from the VIN. It identifies that specific engine unit rather than the vehicle. Where it’s stamped varies by manufacturer. It matters when an engine has been swapped, since the engine may no longer match what the VIN says.

Quick answers to common questions

What’s the difference between BHP and HP? BHP is horsepower measured at the crankshaft, before driveline losses. In everyday spec sheets the two are usually the same number. Both are larger than wheel horsepower.

What are the main types of engines? There’s no single official list of five. Common ways to classify car engines are by fuel and ignition (spark-ignition gasoline vs compression-ignition diesel), by operating cycle (four-stroke vs two-stroke), by cylinder layout (inline, V, flat), by aspiration (naturally aspirated, turbocharged, supercharged), and by design (reciprocating piston vs rotary Wankel). Hybrid systems pair one of these with electric motors.

What are the most common engines in cars? Globally, four-cylinder gasoline engines of roughly 1.0–2.5 L are the most common in passenger cars, increasingly with turbochargers and often as part of hybrid systems. Larger V6 and V8 engines remain common in pickups and large SUVs, especially in North America.

What do SUV and XUV stand for? SUV stands for sport utility vehicle. XUV isn’t a standard industry category. It’s mostly used as a model-name prefix, notably by Mahindra. Neither term says anything about the engine.

Where to go next

Each part of a spec sheet has its own deeper guide in this section:

Keep exploring

Guides from other topics

All topics →