Diesel Engines

Common Rail (CRDi) Diesel Injection Explained

How a common rail (CRDi) diesel fuel system works, part by part, plus its multiple injections, advantages, disadvantages, failure signs and maintenance tips.

On this page
  1. What a CRDi fuel system is
  2. How common rail injection works, part by part
  3. Multiple injections: pilot, main and post
  4. How common rail differs from older diesel injection
  5. Advantages of CRDi
  6. Disadvantages of a CRDi engine
  7. Signs of common rail problems
  8. Keeping a common rail system healthy
  9. Is a CRDi engine good?
  10. Common rail names you might see

What a CRDi fuel system is

CRDi stands for common rail direct injection. It is the fuel injection system used on most modern road diesels. A high-pressure pump fills a shared tube, the rail, with fuel at very high pressure. Every injector is connected to that rail, which is why it is “common”. The engine computer then opens each injector electrically, for exactly as long as it needs to, at exactly the moment it chooses.

The key idea is that pressure generation is separated from injection. The pump only has to keep the rail at the target pressure; the injectors and computer decide timing and quantity. Older diesel systems tied all three together mechanically.

“CRDi” is most closely associated with Hyundai and Kia badging, but the same technology sits under many other names, listed at the end of this article. For where injection fits into the overall engine, see how diesel engines work.

How common rail injection works, part by part

Low-pressure supply and filtration

Fuel leaves the tank via a lift pump, which may be electric or built into the high-pressure pump. It passes through a fuel filter and water separator. Common rail parts are made to very tight tolerances, so filtration is finer than on older diesels, and keeping water out is critical.

High-pressure pump

The high-pressure pump, usually driven by the engine, raises fuel to injection pressure. Modern systems typically operate somewhere in the range of about 1,600 to 2,500 bar (roughly 23,000 to 36,000 psi) at their maximum, with some newer systems rated higher. Pressure in the rail is varied with engine load and speed; it’s usually much lower at idle.

The pump is lubricated and cooled by the diesel fuel passing through it. That’s one reason contaminated fuel or gasoline in the tank can destroy it quickly.

The rail, pressure sensor and pressure control

The rail is a thick-walled tube or forged block that acts as an accumulator, storing a volume of pressurised fuel so that each injection sees nearly the same pressure. A rail pressure sensor reports actual pressure to the computer. Pressure is controlled by a metering valve on the pump inlet, a pressure control valve on the rail, or both, depending on the design. A mechanical pressure relief valve may also be fitted as a safety backstop.

Injectors (solenoid and piezo)

Each injector is fed from the rail by its own high-pressure line. Inside, a control valve holds the nozzle needle shut using fuel pressure. When the computer energises the injector, the balance of pressure changes, the needle lifts, and fuel sprays through tiny holes in the nozzle tip as a very fine mist.

  • Solenoid injectors use an electromagnet to move the control valve.
  • Piezo injectors use a stack of piezoelectric crystals that change shape when voltage is applied. They respond faster, allowing more and smaller injection events.

Some fuel is used to operate the injector and returns to the tank through a leak-off or return line. Excess return flow is a common diagnostic sign of a worn injector.

The engine control unit

The ECU reads crank and cam position, accelerator position, boost, air mass, temperatures and rail pressure. From that it calculates rail pressure, injection timing, the number of injections and the quantity of each, for every cylinder, every cycle. On a common rail engine the ECU also does the job of the diesel governor, holding idle speed and limiting maximum speed in software.

Multiple injections: pilot, main and post

Because injection is electrically controlled, a common rail system can inject several times per combustion cycle. Some systems can do five or more.

  • Pilot injection: a tiny amount of fuel just before the main injection. It starts combustion gently, so the main charge burns with a softer pressure rise. This is the main reason modern diesels clatter far less than older ones.
  • Main injection: the bulk of the fuel, producing the power.
  • Post injection: small amounts injected late in the cycle. These can burn off soot in the cylinder or send unburned fuel into the exhaust to heat the oxidation catalyst for DPF regeneration.

How common rail differs from older diesel injection

Before common rail, most diesels used one of these:

  • Pump-line-nozzle systems (inline or rotary/distributor pumps): a mechanical pump generated each pressure pulse and timed it, and spring-loaded injectors popped open at a set pressure. Injection pressure rose and fell with engine speed, so low-speed injection was relatively coarse.
  • Unit injectors: each injector had its own pump, driven by a camshaft lobe, producing high pressure but with limited control over multiple injections. Some later versions added electronic control.
  • Hydraulically actuated electronically controlled unit injectors (HEUI): used high-pressure engine oil to pressurise fuel inside each injector; found on some North American truck engines.

Common rail’s advantage is that full pressure is available at almost any engine speed, and timing is limited mainly by how fast the injector can open and close.

Advantages of CRDi

  • Quieter, smoother running, mainly thanks to pilot injection.
  • Better atomisation from higher pressure, which gives more complete combustion, less soot and better fuel economy.
  • Strong low-speed torque, since high pressure is available even at low rpm.
  • Precise control for emissions, which is why common rail made it practical for diesels to meet modern standards alongside EGR, DPF and SCR.
  • Easier cold starts than many older mechanical systems, with very little warm-up time needed in mild weather.

Disadvantages of a CRDi engine

  • Very sensitive to fuel quality. Water, dirt or the wrong fuel can damage the pump and injectors. Because the system is all connected, debris from a failing pump can travel to every injector.
  • Expensive parts. High-pressure pumps and injectors cost significantly more than many older mechanical parts, and a contaminated system may need several components replaced together.
  • Diagnosis needs electronics. Problems often show up as fault codes or subtle rail-pressure deviations that need a scan tool and tests such as return-flow checks.
  • Complexity. More sensors, more wiring and more software means more things that can fail.
  • Safety. Rail pressure is high enough to cause serious injury. High-pressure lines should never be cracked open with the engine running, and fuel lines generally shouldn’t be loosened to bleed air the way older diesels were. See how to restart a diesel that ran out of fuel for the correct approach.

Signs of common rail problems

Common symptoms that may point to the fuel system include:

  • Hard starting or long cranking, particularly when warm.
  • Rough or uneven idle, or a misfire.
  • Loss of power or the engine going into limp mode.
  • More smoke than usual; see what diesel smoke colours mean.
  • Knocking, which can come from a leaking or sticking injector.
  • Fault codes for rail pressure too low, too high, or not following its target.
  • Fuel smell or visible leaks.

A leaking injector can also wash fuel into the oil. That and other common failures are covered in common diesel engine problems.

Keeping a common rail system healthy

  • Change fuel filters on schedule and drain the water separator if your vehicle has a manual drain.
  • Buy fuel from busy stations where possible, and avoid running the tank nearly empty, which can draw in sediment and let air into the system.
  • Never put gasoline in the tank. Even small amounts reduce lubrication; see what happens if you put gasoline in a diesel.
  • Use the correct fuel grade for your climate in winter.
  • Keep service work clean. Opening any part of the fuel system lets dirt in; workshops use caps and plugs for this reason.
  • Avoid long periods of idling where you can; low-load running brings its own problems, explained in why you shouldn’t let diesels idle.

Is a CRDi engine good?

For most drivers, yes. Common rail is the reason modern diesels are quieter, cleaner and more economical than older designs, and it is now standard on nearly all road-going diesels. The trade-off is that it is less forgiving of bad fuel and poor maintenance, and repairs are more expensive when something does go wrong. If you buy a used CRDi vehicle, a service history showing regular fuel filter changes is a good sign.

Common rail names you might see

Manufacturers brand their common rail diesels differently. Examples include CRDi (Hyundai and Kia), CDI (Mercedes-Benz), HDi and BlueHDi (Peugeot and Citroën), dCi (Renault), TDCi (Ford), JTD and MultiJet (Fiat), D-4D (Toyota) and later TDI engines from the Volkswagen Group. Note that some names, such as TDI, were also used on older engines that were not common rail.

The complete guide to diesel engines

How Diesel Engines Work: Principle, Parts and the Four-Stroke Cycle
Read the guide

Keep exploring

Guides from other topics

All topics →