A timing chain connects the engine’s crankshaft to its camshaft or camshafts and keeps them turning in a fixed relationship. That keeps the intake and exhaust valves opening and closing at exactly the right moments as the pistons move up and down. Without it, the camshaft wouldn’t turn, the valves wouldn’t operate, and the engine couldn’t run.
It’s a metal chain, similar in principle to a bicycle chain but far stronger, running inside the engine and lubricated by engine oil. On many engines it’s designed to last a very long time, but it can wear, and its guides and tensioner can fail.
How a timing chain links the crankshaft and camshaft
The crankshaft sits at the bottom of the engine and is turned by the pistons. The camshaft sits higher up, in the cylinder head on overhead cam engines or in the block on pushrod engines, and its lobes push the valves open. The timing chain wraps around a sprocket on the crankshaft and one or more sprockets on the camshaft(s), so when the crankshaft turns, the camshaft turns with it.
Because chain and sprocket teeth mesh, the chain can’t slip the way a smooth belt can. As long as the chain stays tight and intact, the camshaft stays exactly where it should be relative to the pistons.
Why the camshaft turns at half speed
In a four-stroke engine, each cylinder needs its intake and exhaust valves to open once every two revolutions of the crankshaft. So the camshaft has to turn once for every two turns of the crankshaft. The chain achieves this through sprocket size: the camshaft sprocket has twice as many teeth as the crankshaft sprocket.
For more on how that 2:1 relationship underpins valve and ignition timing, see our engine timing guide.
The parts of a timing chain system
A timing chain isn’t just a chain. A typical setup includes:
Sprockets
Toothed wheels on the crankshaft and camshaft(s). Some engines have additional idler sprockets, or a second chain stage to reach the cylinder heads on V engines. On engines with variable valve timing, the cam sprocket is often part of a cam phaser, which can rotate the camshaft slightly relative to the sprocket while the engine runs (see variable valve timing, CVVD and camless engines).
Guides
Curved rails, usually with a plastic or nylon wear surface on a metal or plastic backing, that the chain slides along. They stop the chain from slapping and whipping as it runs. Guide wear surfaces can crack or break with age and heat, and broken pieces can end up in the oil pan and block the oil pickup.
Tensioner
A device that presses on the slack side of the chain, usually through a pivoting guide, to keep it tight. Many tensioners are hydraulic, using engine oil pressure plus a spring. Some have a ratchet to stop the chain going slack when oil pressure drops after shutdown. A weak tensioner lets the chain slap and rattle, especially in the first seconds after a cold start before oil pressure builds.
Types of timing chain
- Roller chain: links with rollers on pins, like a bicycle chain. Used as single-row, double-row (duplex) or triple-row chains, depending on load.
- Silent chain (inverted-tooth chain): built from stacked toothed plates that mesh with the sprocket teeth. As the name suggests, it tends to run more quietly and is common on many modern engines.
Some pushrod and heavy-duty engines skip the chain altogether and use timing gears, with the crank and cam gears meshing directly.
Other jobs a timing chain can do
Depending on the engine, the timing chain (or a secondary chain driven from it) may also drive:
- The oil pump
- Balance shafts
- A high-pressure fuel pump on some direct-injection engines
- The water pump on some designs
How long does a timing chain last?
Most modern timing chains have no scheduled replacement interval and are intended to last for a very long time, often the life of the engine, provided the oil is changed on schedule with the correct grade. In practice, life varies a lot by design, maintenance and driving conditions. Some engines are known for chain or tensioner problems at moderate mileage, while others routinely cover very high mileages on the original chain.
What “chain stretch” really means
The steel plates of a chain don’t literally stretch like rubber. What happens is that the pins and the bushings or holes they sit in wear slightly. With dozens of links, those tiny amounts of wear add up, so the chain becomes effectively longer. The tensioner takes up the slack for a while, but the extra length also shifts the camshaft’s position relative to the crankshaft, retarding cam timing. Once wear exceeds what the tensioner can handle, the chain can slap, rattle and, eventually, jump a tooth.
Dirty oil, extended oil change intervals, low oil level and the wrong oil all speed up this wear, because abrasive particles and thin oil films attack the pins and bushings.
Signs of a worn timing chain
Common warning signs include:
- Rattling or slapping from the front of the engine, often loudest for a few seconds after a cold start
- Check engine light, often with crankshaft/camshaft correlation codes or cam timing codes
- Rough idle, misfires or reduced power, as cam timing drifts
- Metal particles in the oil at an oil change (also possible from other parts, so a reason to investigate rather than proof)
If you notice these, it’s worth having the engine diagnosed soon. Chain replacement is usually a big job, since the front of the engine often has to be taken apart to reach it, but replacing a worn chain is generally far cheaper than repairing the damage a failed one can cause.
What happens if a timing chain breaks or jumps?
If the chain breaks or jumps several teeth, the camshaft is no longer synchronized with the crankshaft. The engine will usually stop running or run very badly. In an interference engine, the pistons can strike open valves, causing bent valves and possibly more damage. In a non-interference engine, the engine usually stops without that damage. See interference vs non-interference engines for how this works, and what happens if valve timing is incorrect for smaller timing errors.
Keeping a timing chain healthy
- Change the oil and filter at the intervals in the owner’s manual, or sooner under severe conditions such as frequent short trips, towing or dusty driving.
- Use oil that meets the manufacturer’s specification.
- Keep the oil level topped up; low oil affects both lubrication and hydraulic tensioner pressure.
- Don’t ignore a start-up rattle or cam/crank correlation codes.
- When a chain is replaced, guides, tensioners and sprockets are usually replaced at the same time.
If you’re weighing a chain-driven engine against a belt-driven one, our comparison of timing belt vs timing chain covers lifespan, noise and costs side by side.