Timing and Valvetrain

Engine Timing Explained: Ignition Timing, Valve Timing and Timing Wheels

How engine timing works: valve timing, ignition timing and injection timing, plus timing marks, degree wheels, trigger wheels and the signs of bad timing.

On this page
  1. What “timing” means in an engine
  2. Valve timing: keeping the camshaft in step with the crankshaft
  3. Ignition timing: when the spark fires
  4. Injection timing in diesels and direct-injection engines
  5. Timing wheels: degree wheels and trigger wheels
  6. How timing is checked and set
  7. What bad timing feels like
  8. Where to go next

What “timing” means in an engine

When mechanics talk about “timing” they can mean several different things. All of them come down to the same idea: certain events inside the engine have to happen at a precise point in the piston’s travel, and the engine has to keep those events in step thousands of times a minute.

There are three main kinds of timing in a piston engine:

  • Valve timing (also called mechanical or cam timing): when the intake and exhaust valves open and close relative to the piston.
  • Ignition timing: when the spark plug fires in a gasoline engine.
  • Injection timing: when fuel is sprayed into the cylinder, which matters most in diesels and direct-injection gasoline engines.

Valve timing is set by the physical connection between the crankshaft and camshaft. Ignition and injection timing are set by the distributor on older engines or by the engine computer on modern ones. A problem with one is not necessarily a problem with the others, which is why it helps to be clear about which kind of timing you mean.

One cycle, two revolutions

A four-stroke engine runs through intake, compression, power and exhaust. Each stroke is one trip of the piston up or down the cylinder, and the full cycle takes two turns of the crankshaft, or 720 degrees. One “revolution” of an engine simply means one full 360-degree turn of the crankshaft, so a four-stroke cylinder fires once every two revolutions.

Each valve only needs to open once per cycle, so the camshaft turns at half crankshaft speed. That 2:1 ratio is built into the size of the sprockets or gears that connect the two shafts.

TDC, BTDC and degrees of crankshaft rotation

Timing is measured in degrees of crankshaft rotation relative to top dead center (TDC), the point where the piston is at the very top of its stroke. You’ll see figures such as:

  • BTDC: before top dead center
  • ATDC: after top dead center
  • BBDC / ABDC: before or after bottom dead center

So “10 degrees BTDC” means the event happens when the crankshaft is still 10 degrees short of bringing the piston to the top. Every piston reaches TDC twice per cycle, once at the end of compression and once at the end of exhaust, and timing work always needs to know which of the two you are looking at.

Valve timing: keeping the camshaft in step with the crankshaft

The camshaft’s lobes push the valves open, and springs close them again. For the engine to breathe properly, each valve has to open and close at a specific crankshaft angle. The intake valve, for example, usually opens slightly before TDC at the end of the exhaust stroke and closes some way after bottom dead center, so the cylinder can keep filling while the air is still moving in. The short period when both valves are open is called overlap, which we cover in detail in valve overlap and exhaust reversion explained.

Timing belts, chains and gears

Three methods are used to drive the camshaft from the crankshaft:

  • Timing belts: toothed, fiber-reinforced rubber belts running outside the engine behind a cover. They are quiet and light but must be replaced at intervals set by the manufacturer.
  • Timing chains: metal chains running inside the engine, lubricated by engine oil. They are usually expected to last much longer, though their guides and tensioners can wear. Our article on what a timing chain does for an engine explains the parts involved.
  • Timing gears: gears that mesh directly. They are very durable and are found in many heavy-duty diesel engines, some older pushrod gasoline engines, and various industrial and small engines where the crank and cam sit close together.

For a side-by-side look at the first two, see timing belt vs timing chain. How far the cam sits from the crank, and therefore which drive is practical, depends on the valve train layout, which is covered in the three types of valve trains.

Timing marks

When a belt or chain is installed, the crankshaft and camshaft sprockets have to be lined up in a specific relationship. Manufacturers stamp timing marks on the sprockets, pulleys, covers or engine block for this. With the crankshaft at the specified position (often TDC on cylinder 1), the marks line up and the belt or chain goes on. Some modern engines have no reliable marks and instead require special locking tools that pin the shafts in place.

If the belt or chain is installed one tooth off, or later jumps a tooth, the valve timing will be wrong. The consequences range from poor running to serious damage, as explained in what happens if valve timing is incorrect. Whether a total loss of timing bends valves depends on whether the engine is an interference design, which we cover in interference vs non-interference engines.

Variable valve timing

Fixed valve timing is always a compromise between low-speed smoothness and high-speed power. Most modern engines use variable valve timing, typically a hydraulic cam phaser that can rotate the camshaft a few degrees relative to its sprocket while the engine runs. Some go further and vary valve lift or duration, and a handful of experimental engines do away with the camshaft altogether. See variable valve timing, CVVD and camless engines for how these systems work.

Ignition timing: when the spark fires

In a gasoline engine the spark plug ignites the compressed air-fuel mixture. The point at which it fires is the ignition timing. Our guide to how a gasoline engine ignition system works covers the hardware that makes the spark; this section covers when it happens.

Why the spark fires before top dead center

Combustion isn’t instant. After the spark, the flame takes a short but measurable time to spread through the mixture and build pressure. Ideally, peak cylinder pressure arrives shortly after TDC, when the piston has just started moving down and the pressure can push it most effectively. To make that happen, the spark has to fire before TDC, while the piston is still rising on the compression stroke. This is called ignition advance.

Advance and retard

  • Advancing the timing means firing the spark earlier (more degrees BTDC).
  • Retarding the timing means firing it later.

As engine speed rises, the piston covers more crankshaft degrees in the time it takes the mixture to burn, so the spark generally needs to come earlier. Under light load, when the mixture is thinner and burns more slowly, extra advance also helps.

Too much advance pushes pressure up while the piston is still rising, which can cause knock (also called pinging or detonation), where pockets of mixture ignite on their own. Sustained heavy knock can damage pistons and bearings. Too little advance wastes energy: the burn continues as the piston moves away, which reduces power and efficiency and sends more heat into the exhaust.

Mechanical advance vs computer control

Older engines with a distributor varied timing mechanically:

  • Base (initial) timing was set by rotating the distributor body.
  • Centrifugal advance used spinning weights inside the distributor to add advance as RPM rose.
  • Vacuum advance used a diaphragm connected to engine vacuum to add advance at light load.

Modern engines calculate ignition timing in the engine control unit (ECU) using a crankshaft position sensor, a camshaft position sensor, load and temperature inputs, and usually one or more knock sensors. If the ECU detects knock, it retards timing on the affected cylinder until the knock stops. This lets modern engines run closer to the ideal timing than a fixed mechanical system ever could.

Injection timing in diesels and direct-injection engines

A diesel has no spark plug; fuel ignites from the heat of compression the moment it is injected. That makes injection timing the diesel equivalent of ignition timing. Older diesels set it mechanically through the position of the injection pump, which had to be timed to the engine. Modern common-rail diesels control injection electronically and often split each combustion event into several small injections.

Direct-injection gasoline engines also have injection timing, since fuel is sprayed straight into the cylinder rather than into the intake port. The ECU controls both injection and ignition timing on these engines.

Timing wheels: degree wheels and trigger wheels

“Timing wheel” is used for two quite different parts, which causes a lot of confusion.

Degree wheels

A degree wheel is a tool, not an engine part. It’s a large disc marked in degrees, bolted temporarily to the front of the crankshaft and read against a fixed pointer. Engine builders use one to:

  • Find true TDC precisely, usually with a piston stop
  • “Degree” a camshaft, checking that the valves open and close at the angles on the cam card
  • Check or set the intake centerline when installing an aftermarket cam

Degree wheels are typically somewhere around 6 to 12 inches across; larger wheels are easier to read accurately.

Trigger (reluctor) wheels

A trigger wheel, also called a reluctor or tone wheel, is a permanent part of the engine. It’s a toothed or slotted ring on the crankshaft (and often the camshaft) that passes a position sensor. The ECU counts the teeth to work out engine speed and crankshaft angle.

Most crank trigger wheels have a gap formed by one or more missing teeth so the ECU can recognize a reference point. Two common patterns are 36-1 (36 tooth positions with one missing) and 60-2 (60 positions with two missing). A camshaft sensor adds a second signal so the ECU can tell which stroke each cylinder is on, since the crank alone passes TDC twice per cycle.

If a trigger wheel is damaged, loose or the wrong pattern for the ECU, the engine may misfire, run with incorrect timing or not start at all.

How timing is checked and set

Older distributor engines

On a typical older engine with a distributor, base ignition timing is set roughly like this (always follow the specific engine’s service procedure):

  1. Bring cylinder 1 to TDC on its compression stroke and confirm the timing marks line up.
  2. Check that the distributor rotor points to the cylinder 1 terminal on the cap.
  3. Start the engine and let it reach operating temperature.
  4. Disconnect and plug the vacuum advance line if the procedure calls for it.
  5. Aim a strobe timing light, triggered from the cylinder 1 plug wire, at the crankshaft pulley marks.
  6. Loosen the distributor clamp and rotate the distributor until the mark aligns with the specified number of degrees, then tighten it.

Can you time an engine without a timing light?

Yes, with limits. On points-type ignition, static timing is a long-established method: with the engine off and the crankshaft set to the specified mark, the distributor is rotated until the points just begin to open, which can be detected with a test light across the points. This gets close to the correct base timing but doesn’t show what the advance mechanisms are doing at speed.

Some people also adjust timing by ear or with a vacuum gauge, advancing until the engine runs best and then backing off. That can get a running engine into the right area, but it is rough and doesn’t guarantee freedom from knock under load. A timing light checked against the factory specification remains the reliable method on distributor engines.

Modern computer-controlled engines

On most modern engines you cannot adjust ignition timing with a wrench at all. The ECU sets it, and technicians check it with a scan tool that reads the commanded timing, knock retard and sensor data. When there’s a timing problem on these engines, the cause is usually mechanical (a stretched chain or jumped belt), a sensor or trigger wheel fault, or a variable valve timing fault, not a “setting” that has drifted. Mechanical valve timing is still set by aligning marks or using locking tools whenever the belt or chain is replaced.

What bad timing feels like

Incorrect timing of any kind tends to show up as some combination of:

  • Hard starting or no start
  • Rough idle or stalling
  • Loss of power, especially at one end of the rev range
  • Pinging or knocking under load (often too much ignition advance)
  • Popping through the intake or exhaust
  • Higher fuel consumption
  • Running hot (often too little ignition advance)
  • A check engine light, often with crankshaft/camshaft correlation or misfire codes

These symptoms overlap with fuel, air and compression problems, so they point toward timing rather than prove it. On a modern car, reading the stored fault codes is the sensible first step.

One related but separate idea is firing order: the sequence in which the cylinders fire. Timing is when a cylinder fires; firing order is which cylinder fires next. Our engine firing order explainer covers why most four-cylinder engines use 1-3-4-2.

Where to go next

Keep exploring

Guides from other topics

All topics →