The three main types of valve train are:
- Overhead valve (OHV), also called a pushrod engine: the camshaft sits in the engine block and operates the valves through lifters, pushrods and rocker arms.
- Single overhead cam (SOHC): one camshaft per cylinder head (or per bank on a V engine), mounted above the valves.
- Double overhead cam (DOHC): two camshafts per cylinder head or bank, usually one for the intake valves and one for the exhaust valves.
All three put the valves in the cylinder head. They differ in where the camshaft is and how its motion reaches the valves. An older fourth layout, the flathead or side-valve engine, is covered further down.
What a valve train does
The valve train is everything that opens and closes the engine’s intake and exhaust valves. It usually includes the camshaft, the parts that transfer the cam’s motion (lifters, pushrods, rockers or followers), the valves themselves, and the valve springs that close them.
The camshaft is driven from the crankshaft at half speed by a timing belt, chain or gears, so each valve opens once every two crankshaft revolutions. Where the camshaft sits largely decides which of those drives is practical. Our engine timing guide explains how that relationship is set and maintained.
Overhead valve (OHV or pushrod)
In an OHV engine, the camshaft is in the engine block, close to the crankshaft. Each cam lobe pushes up a lifter (tappet), which pushes a long, thin pushrod up to the cylinder head. There, a rocker arm pivots and pushes the valve open. The valve spring closes it again as the lobe rotates away.
Strengths:
- Compact overall engine size, particularly in V engines, because the cylinder heads don’t carry camshafts
- One camshaft can serve both banks of a V8
- The short distance between crank and cam suits a short chain or gear drive
- Relatively simple and robust
Limitations:
- More moving mass between the cam and the valve, which can limit RPM
- Usually two valves per cylinder (four-valve pushrod designs exist but are uncommon)
- Port and valve layout is more constrained than with overhead cams
OHV is closely associated with American V8s. GM’s LS and later small-block V8s and Chrysler’s modern Hemi V8s are well-known pushrod engines.
Single overhead cam (SOHC)
In an SOHC engine, one camshaft sits in the cylinder head above the valves. V engines have one camshaft in each head. The cam operates the valves either directly or through short rocker arms or followers.
Strengths:
- Far less moving mass than a pushrod layout, allowing higher RPM
- Simpler and usually cheaper than DOHC
- Can operate two, three or four valves per cylinder with rocker arms
Limitations:
- One camshaft serves both intake and exhaust valves, which limits how freely the valves can be arranged
- Separate intake and exhaust variable timing isn’t possible with one shaft (though the whole cam can still be phased)
- A longer belt or chain is needed to reach the head
SOHC engines were very common in cars from the 1970s through the 1990s and remain common in motorcycles and some smaller car engines.
Double overhead cam (DOHC)
A DOHC engine has two camshafts per cylinder head, typically one for the intake valves and one for the exhaust valves. A V6 or V8 DOHC engine therefore has four camshafts, which is where “quad cam” comes from.
Strengths:
- Makes four valves per cylinder straightforward, which improves breathing
- Allows a central spark plug position, which helps combustion
- Intake and exhaust cam timing can be varied separately with phasers
- Low valve train mass, suiting high RPM
Limitations:
- More parts and a larger, heavier cylinder head
- Longer, more complex belt or chain drive
- Generally more expensive to build and service
DOHC is the most common layout in modern passenger car engines.
Comparison table
| OHV (pushrod) | SOHC | DOHC | |
|---|---|---|---|
| Camshaft location | Engine block | Cylinder head (one per head) | Cylinder head (two per head) |
| Typical valves per cylinder | 2 | 2–4 | 4 |
| Parts between cam and valve | Lifter, pushrod, rocker | Rocker/follower or direct | Follower or direct (bucket) |
| Typical cam drive | Short chain or gears | Belt or chain | Belt or chain |
| High-RPM ability | Lower | Moderate to high | High |
| Engine height and width | Compact | Taller head | Tallest/widest head |
| Separate intake/exhaust phasing | No | No | Yes |
These are general patterns, and individual engines can break them.
What about flathead (side-valve) engines?
Before overhead valve engines became dominant, many engines used a flathead or side-valve layout. The camshaft was in the block, and the valves sat beside the cylinder in the block itself, facing upward. The cylinder head was a simple flat cover. Flatheads were simple and cheap, and the Ford flathead V8 is a famous example, but the combustion chamber shape limited compression and breathing. Today side-valve designs survive mostly in older or simpler small engines. Some sources include the flathead as one of the “three types” instead of separating SOHC and DOHC.
How the cam actually pushes the valve: rockers, followers and buckets
Within overhead cam engines, several methods transfer cam motion to the valve:
- Direct-acting buckets: the cam lobe presses on a cup-shaped bucket sitting over the valve stem. Very stiff and light, common in DOHC engines.
- Finger followers (roller rocker followers): a short lever pivots on a hydraulic lash adjuster at one end, with the valve at the other and a roller under the cam lobe in the middle. Common on modern engines because it reduces friction.
- Rocker arms: a lever pivoting on a shaft, with the cam on one side and the valve on the other. Common in SOHC engines and in all pushrod engines.
Valve clearance (lash) is adjusted with shims, screws or automatically by hydraulic lifters, depending on the design.
How to tell which valve train an engine has
- Look at the cylinder heads. Wide valve covers with one or two camshafts’ worth of space usually mean overhead cams. On a V engine, narrow heads with the intake manifold sitting low in the “V” often indicate pushrods.
- Check the badging or spec sheet. “DOHC”, “16V” on a four-cylinder (four valves per cylinder) or “24V” on a V6 usually indicates double overhead cams.
- Look up the engine code. A service manual or manufacturer specification will state the valve train type.
Beyond the camshaft: variable and camless valve trains
Modern valve trains often add variable valve timing, variable lift or both, and a few experimental engines remove the camshaft entirely, using electronically controlled actuators instead. See variable valve timing, CVVD and camless engines for how those systems work. Whatever the layout, the camshaft still has to stay in step with the crankshaft; our article on what a timing chain does for an engine explains one of the ways that’s done.