Engine Specs

Is a 5.7 L engine the same as a 350?

350 cubic inches is about 5.7 liters, so the size is the same. But not every 5.7 L engine is a Chevy 350. Here's how the LS1, HEMI and others differ.

On this page
  1. The math: 350 cubic inches in liters
  2. Why “350” and “5.7” became interchangeable
  3. The classic Chevy 350 family
  4. 5.7 L engines that are not a Chevy 350
  5. How to identify what you actually have
  6. Bottom line

In displacement terms, yes. 350 cubic inches is about 5.7 liters, so “350” and “5.7 L” describe the same engine size in different units. That’s why, in classic American V8s and especially the Chevrolet small-block, the two names are used interchangeably.

But “same size” doesn’t mean “same engine”. Several quite different V8s, from GM and from other manufacturers, are sold as 5.7 L, and some of them aren’t exactly 350 cubic inches. If you’re buying parts or planning a swap, you need to know which engine you have, not just its displacement.

The math: 350 cubic inches in liters

One cubic inch is about 16.387 cubic centimeters:

350 × 16.387 ≈ 5,735 cc ≈ 5.7 L

The classic Chevrolet 350 has a 4.00-inch bore and a 3.48-inch stroke, which works out to about 349.8 cubic inches across eight cylinders. In metric that’s 101.6 mm × 88.4 mm. You can check this with the displacement formula in our engine capacity guide.

Why “350” and “5.7” became interchangeable

American manufacturers traditionally named engines by cubic inches. As metric figures became standard in the 1970s and 1980s, the same engines were increasingly badged in liters. The Chevy 350 became a “5.7”, the Chevy 305 a “5.0” and the 454 a “7.4”. Owners, mechanics and parts catalogs kept using both names, so “350” and “5.7” came to mean the same thing in everyday talk.

Badge figures are rounded, though. A manufacturer can call any engine of roughly 5.65–5.75 L a “5.7”, whatever its design. Our guide to reading engine specs explains why engine codes are more precise than displacement badges.

The classic Chevy 350 family

The Chevrolet 350 small-block appeared in 1967 and was built in many versions over the following decades. Enthusiasts usually identify them by GM’s RPO codes, for example L48, L82, L98, L05 and L31. Broadly:

  • First-generation (Gen I) small-block 350s: the original family, including carbureted versions and later throttle-body and port-injected ones.
  • Vortec 5700 (L31): a later Gen I-based truck and van engine with revised cylinder heads, generally regarded as a modernized 350.
  • Gen II LT1 and LT4 (1990s): still 350 cubic inches with the same bore and stroke, but with significant changes such as a reverse-flow cooling system. Many parts don’t interchange with Gen I engines.

GM and its suppliers also sold 350s for decades as crate engines and in marine and industrial use.

5.7 L engines that are not a Chevy 350

GM LS1 and LS6

The LS1, introduced in the late 1990s, is marketed as a 5.7 L but displaces about 346 cubic inches (bore 3.898 in, stroke 3.622 in). It’s a third-generation (Gen III) small-block with a different block, heads, firing order and electronics. Some people call it “a 350” informally, but it shares very little hardware with the classic 350, and most parts aren’t interchangeable. The LS6 has the same displacement.

Other GM divisions’ 350s

In the 1960s and 1970s, several GM divisions built their own 350 cubic-inch V8s, each a separate design:

  • Oldsmobile 350
  • Buick 350
  • Pontiac 350

These differ from the Chevy 350 and from each other in block design, bore and stroke, and many parts. There was even an Oldsmobile 5.7 L diesel (sold roughly 1978–1985), derived from the Oldsmobile gasoline V8 design, which is a different engine again.

In the late 1970s GM became controversial for fitting Chevrolet 350s to some Oldsmobile models that buyers expected to have Oldsmobile engines. That’s a reminder that even a factory “350” in a GM car isn’t always the engine you’d assume.

Chrysler 5.7 HEMI and Toyota 5.7

  • Chrysler’s modern 5.7 L HEMI displaces about 345 cubic inches. It’s an entirely different design from any GM engine.
  • Toyota’s 5.7 L V8, used in models such as the Tundra, is also unrelated to the Chevy 350.

Several other manufacturers have offered engines of around 5.7 L. The number on its own tells you only the approximate size.

How to identify what you actually have

If you need to know exactly which engine is in front of you:

  1. Check the VIN. On most US-market vehicles from the 1980s onward, the 8th character of the VIN identifies the engine option. Decode it with the manufacturer’s information for that model year.
  2. Look for casting numbers and stamped codes on the block. On Gen I Chevy small-blocks, a stamped ID pad typically sits at the front of the block next to the passenger-side cylinder head, and the block casting number is on the rear flange. Other engines use different locations.
  3. Check the RPO codes. Many GM vehicles carry a service parts label (often in the glovebox or trunk) listing RPO codes, including the engine code.
  4. Look at the hardware. Coil-near-plug ignition, aluminum blocks and plastic intake manifolds usually point to a later design (such as the LS family) rather than a classic 350. This is only a rough indicator.

When the engine may have been swapped, the block markings matter more than the vehicle’s paperwork.

Bottom line

A 350 and a 5.7 L have the same displacement, and for the classic Chevrolet small-block the names refer to the same engine. But 5.7 L is a size, not a design. LS1s, Oldsmobile/Buick/Pontiac 350s, Chrysler HEMIs and Toyota V8s can all wear a 5.7 or 350 label without sharing parts. Identify the specific engine before you buy components.

The complete guide to engine specs

Engine Specs Explained: How to Read Engine Names and Numbers
Read the guide

Keep exploring

Guides from other topics

All topics →