Engine Parts

Piston Rings Explained: Compression Rings, Oil Rings and How They Seal

Piston rings seal combustion pressure, control oil on the cylinder wall and carry heat away. How each ring works, how they wear and how to test them.

On this page
  1. What do piston rings do?
  2. Where the rings sit on the piston
  3. The three rings
  4. How piston rings seal
  5. Piston ring terms
  6. What piston rings are made of
  7. Blow-by: why a little is normal
  8. How piston rings fail
  9. Symptoms of worn or stuck piston rings
  10. Testing rings: compression and leak-down
  11. Can you replace piston rings without rebuilding the engine?

What do piston rings do?

Piston rings are thin, split metal rings that sit in grooves around the top of each piston. They do three main jobs:

  1. Seal combustion pressure. They stop the high-pressure gas above the piston from leaking past it into the crankcase, so the pressure pushes the piston down instead.
  2. Control oil. They scrape excess oil off the cylinder wall and send it back to the sump, leaving just a thin film for lubrication. If too much oil stays on the wall, it burns.
  3. Transfer heat. The piston crown gets very hot and has no direct contact with coolant. The rings carry a large share of that heat out to the cylinder wall, where the cooling system removes it.

They also help keep the piston stable in its bore. Most car engines use three rings per piston: two compression rings and one oil control ring.

For how the piston and rings fit among the rest of the engine, see our engine parts and functions guide.

Where the rings sit on the piston

Machined into the side of the piston, near the crown, are three ring grooves. The bands of piston material between the grooves are the ring lands. The top ring sits closest to the crown, with the second ring just below it and the oil ring lowest of the three. Below the rings is the wrist pin bore, where the piston connects to its connecting rod, and then the skirt.

The oil ring groove has holes or slots through the back of it. Oil scraped off the cylinder wall drains through them into the inside of the piston and back down to the oil pan.

The three rings

Ring Main job Typical design
Top compression ring Seals combustion pressure; carries much of the heat Hardened or coated face, often barrel-shaped
Second ring Backs up the seal; scrapes oil Tapered face, sometimes with a hooked “Napier” lower edge
Oil control ring Meters the oil film on the cylinder wall Usually three pieces: two thin rails and an expander-spacer

Top compression ring

The top ring does most of the sealing. It sits closest to the flame and has the hardest life: it faces the highest pressures and temperatures. Its face, the edge that touches the cylinder wall, is often barrel-shaped and coated to resist wear and scuffing.

Second ring

The second ring catches some of the gas that slips past the top ring. Its more important job is often oil control. Its face is usually tapered, so it rides over the oil film on the way up and scrapes oil down on the way down. Some second rings have a hooked lower edge, called a Napier ring, to scrape more effectively. Mechanics often call it the scraper or wiper ring.

Oil control ring

The oil ring is usually a three-piece assembly. Two thin steel rails scrape the cylinder wall, and a wavy expander-spacer behind them pushes them outward and holds them apart. Together they leave a very thin film of oil on the wall and send the rest through the groove’s drain holes. Some engines use a one- or two-piece oil ring instead.

How piston rings seal

Ring tension and gas pressure

A ring is made slightly larger than the bore and squeezed in when installed, so it presses outward against the cylinder wall. This ring tension gives a basic seal at low pressure.

Most of the sealing force on the compression rings, though, comes from combustion gas itself. On the compression and power strokes, gas pressure gets into the small gap above and behind the top ring. It pushes the ring outward against the cylinder wall and down against the bottom of its groove. The higher the cylinder pressure, the harder the ring is pressed into place. This is why a ring that sticks in its groove because of carbon stops sealing well. The gas can no longer push it out.

Why rings have a gap

Every ring is split, with a small end gap where the two ends meet. The gap lets the ring be fitted over the piston, and lets it expand as it heats up without the ends butting together. If the gap is too small, the ends can touch when hot, which can break the ring or scuff the cylinder. Too large and more gas leaks through.

When rings are installed, the gaps are staggered around the piston, not lined up. Manufacturers and ring makers specify the gap and the gap positions. Builders check each ring’s gap in the bore during assembly.

The cylinder wall’s role and break-in

Rings can only seal against a properly finished cylinder wall. When cylinders are machined, they are honed to leave a fine crosshatch pattern of shallow scratches. The crosshatch holds a little oil and gives new rings a surface to wear in against.

During break-in, the first period of running after a rebuild, the ring faces and cylinder walls wear against each other until they match closely and seal well. Engine builders and manufacturers give specific break-in advice. Varying the engine speed and load, and avoiding long periods of idling or constant speed, is common guidance. Follow the builder’s instructions for your engine.

Piston ring terms

Term Meaning
End gap The gap between the ring ends when it is in the bore
Side (axial) clearance The space between the ring and the top and bottom of its groove
Back clearance The space between the back of the ring and the back of the groove
Radial width How thick the ring is from its face to its back
Axial height How tall the ring is, measured along the piston’s axis
Face profile The shape of the ring’s contact face: barrel, taper and so on
Twist A deliberate built-in tilt that helps the ring seal or scrape
Ring land The piston material between two ring grooves
Blow-by Combustion gas that leaks past the rings into the crankcase

What piston rings are made of

Rings are usually made of cast iron, ductile iron or steel. Their faces are often treated or coated to resist wear and scuffing. Common treatments include chrome plating, plasma-sprayed molybdenum, nitriding (a hardening process) and, in some modern engines, thin hard coatings applied by physical vapor deposition (PVD). The right combination depends on the engine’s cylinder bore material, pressures and temperatures.

Blow-by: why a little is normal

No set of rings seals perfectly. A small amount of combustion gas always gets past them. This is blow-by. It carries moisture, unburned fuel and combustion byproducts into the crankcase.

Engines handle normal blow-by with a positive crankcase ventilation (PCV) system, which draws those gases back into the intake to be burned. As rings wear, blow-by increases, crankcase pressure rises, and oil can be pushed out of seals or into the intake.

How piston rings fail

  • Normal wear. Over a long service life, rings and cylinder walls slowly wear and the seal gradually weakens.
  • Abrasive wear. Dirt drawn in through a damaged air filter, or grit in the oil, wears rings and bores much faster.
  • Sticking. Carbon and sludge can build up in the grooves, especially behind the oil ring, so the ring can’t move freely or drain oil. Infrequent oil changes, lots of short trips and certain engine designs can make this more likely.
  • Overheating. Excess heat can make rings lose tension, or let them scuff against the bore.
  • Detonation. Severe knock can break rings and even crack the ring lands on the piston.
  • Incorrect installation. Rings fitted upside down, with the wrong gaps, or with gaps lined up can cause oil consumption or poor sealing from the start.
  • Bore problems. Worn, tapered or out-of-round cylinders, or glazed walls, keep even new rings from sealing.

Symptoms of worn or stuck piston rings

  • Higher oil consumption. You have to top up oil more often, with no visible leak.
  • Blue-gray exhaust smoke. It is often most noticeable on acceleration, or after decelerating from speed.
  • Low compression, in one or more cylinders.
  • Loss of power, and sometimes harder starting.
  • Oil-fouled spark plugs.
  • Excess crankcase pressure. You may see visible fumes from the oil filler when the engine is running, or oil being pushed out of the dipstick tube or seals.

Other problems can cause the same signs. Worn valve stem seals, for example, also burn oil, often showing as a puff of smoke at startup. A failing turbocharger seal can too. Testing is the way to tell them apart.

Testing rings: compression and leak-down

Compression test. A gauge is screwed into each spark plug hole in turn while the engine is cranked, with the fuel and ignition disabled as your service manual describes. Readings are compared between cylinders. One or more cylinders well below the others suggests a sealing problem.

Wet compression test. If a cylinder reads low, a small amount of engine oil is added through the plug hole and the test repeated. The oil temporarily helps seal the rings.

  • If compression rises noticeably, worn or stuck rings are the likely cause.
  • If it barely changes, the leak is more likely at the valves or the head gasket.

Leak-down test. With the piston at TDC on the compression stroke, regulated compressed air is fed into the cylinder, and a gauge shows the percentage that leaks away. Where you hear the air escape points to the cause:

Air escaping from Likely leak
Oil filler or dipstick tube Piston rings
Throttle body or intake Intake valve
Tailpipe Exhaust valve
Radiator or coolant reservoir (bubbles) Head gasket or a crack
Neighboring spark plug hole Head gasket between cylinders

A leak-down test generally gives a clearer picture than a compression test alone.

Can you replace piston rings without rebuilding the engine?

In most cases, replacing rings means removing the pistons, which means removing the cylinder head and the oil pan and taking out each piston and rod assembly. On some engines that can be done with the engine still in the car. On many others, the engine has to come out. Either way, it is major engine work.

It also rarely makes sense to replace rings alone. The cylinders usually need measuring and honing, or machining if they’re worn. Bearings and gaskets are normally replaced at the same time. Done properly, a ring job ends up close to a partial rebuild.

Some products claim to free up stuck rings, and engine-cleaning treatments are sometimes tried before major work. Results vary, and they can’t restore rings or cylinders that are actually worn. If testing confirms worn rings, the realistic choices are a rebuild, a replacement engine, or living with the oil consumption and monitoring the oil level closely.

The complete guide to engine parts

Engine Parts and Functions: A Labeled Guide to What's Inside
Read the guide

Keep exploring

Guides from other topics

All topics →