Engine Parts

What destroys a crankshaft?

Oil starvation, contaminated oil, failed dampers, detonation, over-revving and bad machining are the main crankshaft killers. Learn the signs and prevention.

On this page
  1. The short answer
  2. Oil starvation and bearing failure
  3. Contaminated or diluted oil
  4. Torsional vibration and a failed harmonic balancer
  5. Thrust bearing wear
  6. Heavy bending loads: detonation, lugging and hydrolock
  7. Over-revving and broken connecting rods
  8. Misaligned main bearing bores
  9. Assembly and machining mistakes
  10. Material and manufacturing defects
  11. What the damage looks like
  12. Warning signs to watch for
  13. How mechanics check a crankshaft
  14. How to protect your crankshaft

The short answer

The most common cause of crankshaft damage is lubrication failure: not enough oil, oil that has broken down, or contaminated oil. When the oil film between the crank and its bearings fails, metal rubs on metal, the bearings wear or spin, and the journals score and overheat.

Other causes include a failed harmonic balancer, heavy detonation or hydrolock, over-revving, a misaligned block, and poor machining or assembly. A crankshaft is one of the strongest parts in an engine. When it is destroyed, it is usually because something else failed first.

For how the crankshaft is built and what each section does, see our crankshaft parts and function guide.

Oil starvation and bearing failure

A crankshaft doesn’t actually touch its bearings when the engine is healthy. It floats on a thin, pressurized film of oil. Lose that film and damage happens quickly. Causes include:

  • Low oil level from leaks, oil burning or simply not checking it
  • Low oil pressure from a worn or failing oil pump, a clogged pickup screen, or a blocked filter
  • Oil starvation in hard cornering, on track or off-road, where oil surges away from the pickup
  • Overdue oil changes, which let oil thicken, sludge up and lose its protective properties
  • The wrong oil for the engine, in viscosity or specification

Once the film breaks down, the bearing shells overheat and wear. In severe cases a bearing can spin in its housing, taking itself out of position and blocking its own oil supply. Rod bearings are often affected first, because they get their oil through passages drilled in the crank from the main bearings. The resulting knock is the classic “rod knock,” and if it continues, the connecting rod can break. Our article on connecting rods and why they break covers that chain of events.

Contaminated or diluted oil

Even a full sump of oil can fail if it is contaminated:

  • Coolant in the oil, often from a failed head gasket or a cracked head or block. It ruins the oil’s ability to lubricate and can turn it milky.
  • Fuel dilution. Fuel getting past the rings thins the oil. Lots of short trips, rich running and some direct-injection engines can make this more likely.
  • Dirt and debris. A torn air filter, a skipped oil filter change, or metal particles from another failing part can all score journals.
  • Leftover debris after a repair. Metal from a previous bearing failure that wasn’t fully cleaned out of oil passages and coolers can destroy a freshly rebuilt engine.

Torsional vibration and a failed harmonic balancer

Every power stroke twists the crankshaft slightly, and it springs back. At certain engine speeds these twists can build into strong torsional vibration. The harmonic balancer (torsional damper) on the front of the crank is there to absorb it. It is often a metal hub and outer ring bonded with rubber, or filled with viscous fluid.

As balancers age, the rubber can harden, crack or separate, and the outer ring can slip or wobble. A failed damper no longer controls the vibration. Over time that can crack the crankshaft, often near the front. A wobbling crank pulley, a misaligned timing mark on the balancer, or a belt that keeps jumping off are signs to have it checked.

Thrust bearing wear

One of the main bearings has flanges, or separate thrust washers, that stop the crankshaft sliding forward and backward. That fore-and-aft play is called end play. If the thrust surfaces wear out, the crank can move too far, damaging the bearing, the crank’s thrust faces and sometimes the block.

Things that push hard on the crank lengthwise can speed up thrust wear:

  • resting your foot on the clutch pedal for long periods in a manual car
  • a clutch with an unusually heavy release load
  • an automatic transmission’s torque converter that is installed incorrectly or swells under pressure

Excessive end play is usually found by a mechanic, who measures movement at the crank pulley.

Heavy bending loads: detonation, lugging and hydrolock

  • Detonation (knock). Uncontrolled combustion produces sharp pressure spikes that hammer the pistons, rods, bearings and crank. It is more likely with low-octane fuel in an engine that needs higher octane, overheating, carbon buildup, or aggressive tuning.
  • Lugging. Running at very low rpm under heavy load, such as flooring it in too high a gear, puts high bending loads on the crank and bearings.
  • Hydrolock. If water or another liquid enters a cylinder, for example from driving through deep water, the piston can’t compress it. This more often bends a connecting rod than breaks the crank. A bent rod can then cause bearing and crank damage.

Over-revving and broken connecting rods

Exceeding an engine’s safe rpm sharply increases the inertia loads on the rods and crank. Rev limiters prevent most over-revving under power. A missed downshift in a manual car can spin the engine far beyond redline through the drivetrain, though, and the limiter can’t stop that.

If a connecting rod or rod bolt breaks, the flailing rod can strike and gouge the crankshaft, sometimes ruining it along with the block.

Misaligned main bearing bores

The main bearing bores in the block must line up in a straight line. If the block distorts, the crank is forced to flex with every revolution, and that steady bending can lead to fatigue cracks. Distortion can come from severe overheating, mismatched main caps, or incorrect torque on the main cap bolts. Machine shops check this and can correct it with a process called line boring or line honing.

Assembly and machining mistakes

Many crankshaft failures in rebuilt engines trace back to the rebuild itself:

  • Wrong bearing clearances. Too tight starves the bearing of oil. Too loose lets oil pressure drop and the crank take hammering loads.
  • Poorly finished fillets after regrinding. If the radiused corner where a journal meets the web is ground too sharp, or burned, it becomes a weak spot for cracks.
  • Incorrect bolt torque on main caps, rod caps or the flywheel.
  • Dirt left in oil passages or on bearing backs.
  • Not priming the oil system before the first start, so the bearings run dry for the first few seconds.

Material and manufacturing defects

Defects are uncommon in factory and reputable aftermarket parts, but they do happen. Examples include inclusions or porosity in the metal, improper heat treatment, and rough machining marks at stress points. They usually show up as a fatigue crack that grows over time until the crank breaks.

What the damage looks like

Type of damage What it looks like Usual cause
Scored journals Grooves or scratches on a journal Debris in the oil, early lubrication failure
Overheated (discolored) journals Blue or dark straw-colored marks Severe oil starvation or a spun bearing
Worn or out-of-round journals Measurable taper or ovality Long-term wear, poor lubrication
Worn thrust faces Grooved or stepped thrust surfaces Thrust loads from clutch or converter
Fatigue crack Fine line, usually starting at a fillet Repeated bending or twisting: damper failure, misalignment, bad regrind
Fracture Crank broken in two A fatigue crack that finally grew through, or a sudden huge overload

Warning signs to watch for

  • Oil pressure warning light or a low reading on the gauge, especially at hot idle
  • A deep knock from low in the engine that rises with rpm
  • Metal glitter in the oil, or metal flakes in the oil filter at a change
  • New vibration, or a wobbling crank pulley
  • A clutch pedal that feels different, or a crank pulley that moves in and out, which can point to thrust problems
  • Crankshaft position sensor codes that appear after mechanical work or alongside other symptoms. This is less common, and most CKP codes are electrical. Our engine sensors guide explains them.

If you see an oil pressure warning or hear a new bottom-end knock, the cautious move is to stop the engine as soon as it’s safe and have it diagnosed. Driving on can turn a repairable bearing problem into a destroyed crankshaft and block.

How mechanics check a crankshaft

When an engine is apart, a machine shop typically:

  1. Cleans and visually inspects the journals, fillets and thrust faces.
  2. Measures each journal with a micrometer for size, taper and out-of-round.
  3. Checks straightness by spinning the crank in V-blocks with a dial indicator.
  4. Tests for cracks, commonly with magnetic particle inspection. The crank is magnetized and fine iron particles collect along any crack. Dye penetrant testing is another option.

Depending on the results, the crank may be polished, reground to an undersize with matching bearings, or replaced.

How to protect your crankshaft

Most of this comes down to looking after the oil:

  • Check the oil level regularly, and top up with the grade your manual specifies.
  • Change oil and filter on schedule. Use the shorter “severe service” interval if your driving involves lots of short trips, towing, dusty conditions or extreme temperatures.
  • Never ignore an oil pressure warning.
  • Fix coolant leaks and head gasket problems early so coolant doesn’t reach the oil.
  • Use the octane rating the manufacturer requires.
  • Avoid lugging the engine, and take care with downshifts in a manual.
  • Have a worn or wobbling harmonic balancer replaced.
  • Use a reputable machine shop for any rebuild, and follow its break-in and oil-priming advice.

A well-maintained crankshaft often outlasts the rest of the car. For a broader look at how the crank fits into the engine, see our engine parts and functions guide.

The complete guide to engine parts

Engine Parts and Functions: A Labeled Guide to What's Inside
Read the guide

Keep exploring

Guides from other topics

All topics →