How a diesel engine starts
A diesel has no spark plugs, so it starts using the same trick it uses to run: compressing air until it is hot enough to ignite fuel. When you turn the key, the starter motor spins the engine. Each piston compresses the air in its cylinder, the temperature rises, the injection system sprays in fuel, and once a few cylinders fire, the engine runs on its own.
That makes three things essential for a diesel to start:
- Enough cranking speed, so air is compressed quickly and doesn’t lose too much heat to cold metal or leak past the rings.
- Enough compression, so the air reaches ignition temperature.
- Fuel delivered at the right time and pressure, with no air in the lines.
In cold weather, a starting aid such as glow plugs adds heat to make up for the cold engine. For the full engine cycle, see how diesel engines work.
Compression ratio vs compression pressure
People ask “do diesel engines have compression?” and “what’s the minimum compression for a diesel?”, and the answer depends on which kind of compression you mean.
- Compression ratio is a design figure: how much the cylinder volume shrinks from the bottom of the stroke to the top. It’s fixed when the engine is built.
- Compression pressure is what a gauge reads during a compression test while the engine is cranked. It reflects the ratio but also cranking speed, temperature, valve timing and, importantly, how well the rings and valves seal.
Minimum compression ratio for a diesel
Diesels generally use compression ratios from about 14:1 up to around 22:1 to 25:1. Engineering sources commonly put the practical lower limit for reliable self-ignition of normal diesel fuel at around 14:1. Below roughly 12:1 to 13:1, starting without help becomes difficult or unreliable.
Many modern turbocharged diesels use relatively low static ratios, around 15:1 to 17:1, because the turbo raises the effective pressure once the engine is running and because a lower ratio helps with emissions and peak cylinder pressure. These engines lean on glow plugs and precise injection control for cold starts.
Older indirect-injection diesels often used ratios above 20:1, because heat is lost to the walls of the pre-chamber.
Cranking compression pressure (psi)
Healthy diesels typically read several hundred psi on a compression test, commonly somewhere in the range of roughly 300 to 500 psi, though the right figure depends entirely on the engine. The manufacturer’s specification is what matters, including its minimum value.
Two guidelines apply to almost every engine:
- Consistency matters more than the absolute number. A large difference between cylinders points to a problem. Many technicians look for all cylinders to be within roughly 10 percent of each other, though specs vary.
- Test conditions matter. Readings depend on cranking speed and engine temperature, so tests should be done the way the service manual describes, usually warm and with a fully charged battery. Diesel testing needs a gauge rated for diesel pressures and adapters that fit the injector or glow plug holes.
A low cylinder might be caused by worn rings, a burnt or sticking valve, a head gasket leak or piston damage. Low compression across all cylinders often shows up first as hard starting, white smoke when cold, and blow-by; see how to tell if a diesel has blow-by.
Is 210 psi too much compression?
It depends on the engine.
- For a diesel, 210 psi is not too much; it’s very low. Most diesels would read well above that when healthy, and a diesel cylinder at 210 psi would likely be misfiring or causing hard starting.
- For a gasoline engine, 210 psi is on the high side of normal. Many gas engines read somewhere around 125 to 200 psi depending on design, so 210 psi could be normal for a high-compression engine or could point to carbon build-up. Compare with the manufacturer’s spec and the other cylinders.
Is 12.0:1 a high compression ratio?
Again, it depends on the engine type. For a gasoline engine, 12.0:1 is fairly high, though some modern direct-injection gas engines run that or more. For a diesel, 12.0:1 would be too low to start and run reliably without help.
What causes high compression in one cylinder?
A reading that’s noticeably higher than the others usually means something is taking up space in the combustion chamber or sealing it unusually well. Common causes include:
- Carbon deposits on the piston crown or in the head, which reduce chamber volume and raise compression.
- Oil in the cylinder, for example from a “wet” compression test where oil was added, or from oil getting past valve stem seals or rings. Oil temporarily seals the rings and raises the reading.
- Testing errors, such as a faulty gauge, an uneven cranking speed, or testing that cylinder at a different temperature.
Liquid in a cylinder is dangerous on any engine, because liquid doesn’t compress. Fuel or coolant pooling in a cylinder can cause hydrolock and bent connecting rods.
Why cold starts are harder
In cold weather, several things work against a diesel:
- Cold metal pulls heat out of the compressed air, so the air may not reach ignition temperature.
- Batteries deliver less power, so the engine cranks slower and compresses air less effectively.
- Engine oil is thicker, adding drag.
- Diesel fuel thickens, and in severe cold, waxes in the fuel can crystallise and block filters (gelling).
Starting aids: glow plugs, grid heaters, block heaters
- Glow plugs are small electric heating elements that protrude into each cylinder or pre-chamber. They heat up before and during cranking, and on many modern engines keep operating for a while after start-up to reduce smoke and noise. A failed glow plug can cause rough running and white smoke on cold starts.
- Intake grid heaters warm the incoming air. They’re common on some larger pickup and truck engines.
- Block heaters plug into mains power and keep coolant warm overnight, making cold starts much easier.
- Air starters and hydraulic starters are used on some large industrial and marine engines instead of electric starters.
Many modern diesels with high-speed glow plugs only need a second or two of preheat in mild weather.
How to start a diesel engine properly
Follow your owner’s manual first, but most modern road diesels start like this:
- Turn off unnecessary electrical loads such as heater fan and lights.
- Press the brake (and clutch on a manual).
- Turn the key to “on” or press the start button without starting, and wait for the glow plug or “wait to start” light to go out.
- Crank the engine. Don’t press the accelerator unless the manual says to.
- If it doesn’t start, crank in short bursts, commonly no more than 10 to 15 seconds, and let the starter cool between attempts. Repeat the preheat if needed.
- Once it starts, let it settle briefly, then drive gently until it’s warm rather than leaving it idling for a long time. Our article on why you shouldn’t let diesels idle explains why.
If the engine has run out of fuel or just had a fuel filter change, air in the system must be purged first; see how to start a diesel engine that has run out of fuel.
What can stop a diesel engine from starting
Work through these roughly from easiest to hardest to check:
- Battery and cranking: weak batteries, corroded terminals or a tired starter that cranks slowly. Many diesels need more cranking power than gasoline engines, and some trucks have two batteries.
- Fuel supply: an empty tank, air in the lines, a clogged filter, gelled fuel in cold weather, or water in the fuel.
- Glow plugs or heaters: failed plugs, a bad glow plug relay or control module, or a failed grid heater.
- Fuel injection faults: a weak lift pump, a failing high-pressure pump, low rail pressure on a common rail system, or leaking injectors. See common rail diesel injection for how this system works.
- Sensors and electronics: a failed crankshaft or camshaft position sensor, immobiliser faults, or wiring problems can prevent injection entirely.
- Emissions system lockout: on some vehicles, running the DEF tank empty can stop the engine restarting until it’s refilled; see common diesel engine problems.
- Wrong fuel: gasoline in the tank; see what happens if you put gasoline in a diesel.
- Low compression: worn rings, valve problems or a head gasket failure.
Starting fluid: why to be careful
Ether-based starting fluid can make a reluctant diesel fire, but it’s risky. It ignites very easily and can cause violent, early combustion that may damage pistons, rings or rod bearings. On engines with glow plugs or an intake grid heater, starting fluid can ignite in the intake and cause damage or a fire. Many manufacturers warn against using it at all. If a diesel needs starting fluid to start, there’s an underlying problem that should be found.
What’s the worst thing for a diesel engine?
There’s no single official answer, but contaminated fuel is near the top of most lists. Water or dirt in the fuel, or the wrong fuel altogether, can wreck an expensive injection system quickly. Other common culprits are skipped oil and filter changes, lots of short trips or long idling that stop the engine and its particulate filter from getting hot, and ignoring warning lights.