The core difference in one sentence
An internal combustion engine burns fuel inside the engine, and the hot combustion gases push the moving parts themselves. An external combustion engine burns fuel outside the engine and uses that heat to warm a separate working fluid, such as water turned to steam or a sealed volume of gas, which does the pushing.
Both are heat engines. Both turn heat into mechanical work. The difference is where the fire is and what touches the piston or turbine blades.
What is internal combustion?
Internal combustion means the fuel and air burn in a chamber that’s part of the engine. In a car engine, that chamber is the space above each piston. A charge of air and fuel is drawn in, compressed and ignited. The rapid rise in pressure drives the piston down, and the burnt gases are then pushed out as exhaust. The full sequence is covered in how a car engine works.
Petrol and diesel piston engines are the most familiar examples, but they aren’t the only ones. Gas turbines and jet engines are also internal combustion engines. They burn fuel continuously in a combustion chamber, and the hot gases spin turbine blades directly. They have no pistons, but the fuel still burns inside the engine’s own gas flow.
What is external combustion?
In an external combustion engine, the burning happens in a separate furnace, burner or boiler. Heat passes through a wall, such as boiler tubes or a heater head, into a working fluid that never mixes with the combustion gases. The working fluid expands and drives a piston or turbine.
Are steam engines external combustion engines?
Yes. The steam engine is the classic external combustion engine. Coal, wood, oil or gas burns in a firebox. The heat boils water in a boiler, and the high-pressure steam is piped to cylinders, where it pushes pistons, or to a turbine. The fire never enters the cylinder.
Steam turbines in power stations work on the same principle, just on a much bigger scale and with rotating blades instead of pistons.
Stirling engines
A Stirling engine is another type of external combustion engine. A fixed amount of gas, often air, helium or hydrogen, is sealed inside the engine and shuttled between a hot end and a cold end. Heating the gas makes it expand and push a piston, and cooling it lets it contract again. Because the heat comes from outside, a Stirling engine can in principle run on almost any heat source, including burning fuel, concentrated sunlight or waste heat.
Key differences side by side
| Feature | Internal combustion | External combustion |
|---|---|---|
| Where fuel burns | Inside the engine (cylinder or combustion chamber) | Outside, in a furnace, burner or boiler |
| What does the work | The combustion gases themselves | A separate working fluid (steam, air, helium, etc.) |
| Typical examples | Petrol and diesel engines, gas turbines, jet engines | Steam engines, steam turbines, Stirling engines |
| Fuel | Usually refined fuels: petrol, diesel, natural gas, kerosene | Very flexible: coal, wood, biomass, oil, gas, or non-combustion heat |
| Size and weight | Compact for the power produced | Usually bulkier, because of the boiler or heat exchangers |
| Start-up | Seconds | Often slow, because the working fluid has to heat up first |
| Combustion | Intermittent in piston engines, continuous in turbines | Usually continuous and steady |
| Response to throttle | Quick | Generally slower |
Which is more efficient?
You’ll often read that internal combustion engines are always more efficient. The real picture is more mixed.
- Small and mobile engines: Internal combustion usually wins. Early steam locomotives were very inefficient, generally converting only a small single-digit percentage of their fuel’s energy into work, while modern car engines do several times better. A small steam plant loses a lot of heat through the boiler and the exhaust from the fire.
- Large stationary plants: External combustion can be very competitive. Large modern steam-turbine power stations run at efficiencies broadly comparable to good car engines, because at that scale engineers can use very high steam temperatures and pressures and recover heat carefully.
- In theory: Any heat engine’s efficiency is limited by the temperatures it works between. Stirling engines can, in theory, approach that limit, but practical designs have struggled with heat exchangers, sealing and cost.
So efficiency depends heavily on size, temperatures and design, not just on where the fuel burns.
Why cars ended up with internal combustion
Steam cars were genuinely competitive in the early 1900s. They were smooth, quiet and needed no gearbox, and a Stanley steam car set a land speed record in 1906. But internal combustion pulled ahead for practical reasons:
- Power for its size and weight. Without a boiler, fire and water supply, an internal combustion engine packs much more power into a small space.
- Quick starting. Once the electric starter became common, petrol cars started almost instantly. Steam cars needed time to build pressure.
- Simplicity of fuelling. A petrol car needs only fuel, not fuel and water.
- Cost. Mass-produced petrol cars became far cheaper.
Where external combustion is still used
External combustion is far from dead. It’s just mostly out of sight:
- Power generation: Steam turbines produce a large share of the world’s electricity. In coal, biomass and many gas plants, the heat comes from combustion. Nuclear and some solar thermal plants use the same steam cycle with a non-combustion heat source.
- Combined-cycle plants: These pair a gas turbine (internal combustion) with a steam turbine (external heat) that runs on the gas turbine’s exhaust heat.
- Stirling engines: Some submarines use Stirling engines for air-independent propulsion. Stirling designs have also been tested for solar power and small-scale heat-and-power units.
- Heritage steam: Preserved railways and traction engines keep historic steam running.
Do cars still use internal combustion engines?
Yes. Electric car sales are rising, but most cars on the road worldwide still have an internal combustion engine. Most hybrids also use one, alongside an electric motor and battery. Almost all of these use the four-stroke cycle; the four-stroke Otto cycle explains how it works and where it came from.