Why an engine needs a cooling system
An internal combustion engine turns only part of its fuel’s energy into motion. Much of the rest becomes heat. Most of that heat goes out of the exhaust, but a large amount soaks into the cylinder walls, cylinder head and pistons. Left unchecked, that heat would warp the head, break down the oil and eventually seize the engine.
But the cooling system’s job isn’t simply to make the engine as cold as possible. It’s to hold it at a steady working temperature:
- Too hot, and parts expand beyond their clearances, oil thins and breaks down, and petrol engines become prone to knock.
- Too cold, and fuel doesn’t vaporise and burn as well, oil stays thick, wear increases, emissions rise, and moisture and fuel can build up in the oil.
So a good cooling system warms the engine up quickly, then removes just enough heat to hold it there. For where this heat comes from in the first place, see how a car engine works.
The coolant loop, step by step
Most car engines are liquid-cooled. Coolant circulates in a closed loop:
- The water pump pushes coolant into passages in the engine block, called water jackets.
- Coolant flows around the cylinders and up through the cylinder head, absorbing heat from the hottest parts of the engine.
- The thermostat decides where the hot coolant goes next. If the engine is still warming up, the thermostat stays closed, and coolant takes a short bypass route back to the pump without passing through the radiator. Once the engine reaches its working temperature, the thermostat opens.
- The radiator receives the hot coolant through the top hose. Air flowing through the radiator’s fins, from driving or from the cooling fan, draws heat out of it.
- Cooled coolant leaves the radiator through the bottom hose and returns to the pump to go around again.
Some of the hot coolant is also routed through the heater core to warm the cabin.
The parts and what they do
Water pump
The water pump is usually a simple impeller (a spinning disc with vanes) driven by the auxiliary belt or the timing belt. Many newer engines use electric water pumps, which can vary flow independently of engine speed and even keep running briefly after the engine is switched off.
Water jackets
These are cast passages surrounding the cylinders and running through the cylinder head. Coolant passes directly over the outside of the cylinder walls and around the combustion chambers and exhaust ports, where the most heat collects.
Thermostat
The thermostat is a temperature-controlled valve, usually near where coolant leaves the engine. A traditional thermostat contains a small capsule of wax. When the coolant reaches the thermostat’s rated temperature, the wax melts and expands, pushing the valve open. As coolant cools, a spring closes it again.
Opening temperatures vary by engine, but they commonly fall somewhere around 80-95°C (roughly 180-200°F). Some modern engines use electronically controlled thermostats, which the engine computer can open earlier under heavy load or keep warmer during light cruising for efficiency.
A thermostat that sticks closed causes overheating. One that sticks open makes the engine slow to warm up, with a gauge that reads low and a heater that stays lukewarm.
Radiator
The radiator is a heat exchanger at the front of the car. Coolant flows through rows of thin tubes, which are bonded to thin metal fins that give a large surface area. Air passing through the fins carries the heat away. Most modern radiators are aluminium with plastic end tanks.
Cooling fans
When you’re moving at speed, plenty of air flows through the radiator naturally. In traffic or at idle, it doesn’t, so a fan pulls air through. Most modern cars use electric fans that switch on when coolant temperature rises or the air conditioning is running. Some rear-wheel-drive cars and trucks use an engine-driven fan with a viscous clutch that engages more as temperatures rise.
Pressure cap and expansion tank
The system is sealed and runs under pressure. The pressure cap, on the radiator or the expansion tank, holds pressure up to a set limit. Many cars are rated around 1 bar (roughly 15 psi), but check the cap or manual for yours.
As coolant heats up, it expands. Excess coolant flows into the expansion tank (or overflow reservoir). As it cools and contracts, coolant is drawn back. That’s why the reservoir level marks are different for a cold and a hot engine. Check the level against the “cold” mark with the engine cold.
Heater core
The heater core is a small radiator behind the dashboard. Hot coolant flows through it, and the cabin blower pushes air over it to warm the interior. That’s why the heater only blows warm once the engine has warmed up.
Hoses
Rubber hoses connect the engine, radiator, heater core and expansion tank. They age over time, and a split or swollen hose is a common cause of coolant loss.
Coolant: more than water
Engine coolant, or antifreeze, is usually a mix of water and glycol (most often ethylene glycol), plus corrosion inhibitors. It’s typically used at around a 50/50 ratio, unless the manufacturer specifies otherwise or the coolant comes pre-mixed. It does several jobs:
- Lowers the freezing point, so the engine doesn’t crack in winter
- Raises the boiling point, adding to the effect of pressure
- Prevents corrosion and scale in the block, head, radiator and water pump
- Lubricates the water pump seal
Coolants come in different chemistries, and they aren’t all compatible. Use the type the manufacturer specifies, and don’t mix types without checking, as some combinations can reduce corrosion protection.
Safety: Coolant is toxic if swallowed, and its sweet taste can attract children and pets. Store it securely, and clean up spills promptly.
Why the system is pressurised
A liquid’s boiling point rises with pressure. Running the coolant under pressure lets it reach well above 100°C without boiling. That matters for two reasons:
- Boiling coolant stops cooling. Steam pockets don’t carry heat away well, and they can form against the hottest metal surfaces and cause local overheating.
- A higher temperature difference cools better. The hotter the coolant compared with the outside air, the more heat the radiator can shed.
This is also why you must never open the radiator or expansion tank cap on a hot engine. Releasing the pressure can make the coolant boil instantly and spray out, causing severe burns. Wait until the engine has fully cooled.
Air-cooled engines
Some engines use air instead of liquid. Their cylinders and heads are covered in fins that increase the surface area. Airflow from movement or a fan carries heat away directly. Air cooling is simpler and lighter, with no radiator, pump or coolant to leak, so it’s common on small engines, many motorcycles, and older cars and light aircraft. It’s harder to hold a steady temperature that way, though, which is one reason almost all modern car engines are liquid-cooled. Most two-stroke garden tools are air-cooled; see how a two-stroke engine works.
Why engines overheat
Common causes include:
- Low coolant from a leaking hose, radiator, water pump or heater core
- A thermostat stuck closed
- A failed water pump, or a broken or slipping drive belt
- Cooling fan failure, often noticed as overheating in traffic but not on the open road
- A blocked radiator, either clogged inside or covered with debris outside
- Air trapped in the system after a coolant change that wasn’t properly bled
- A faulty pressure cap that lets coolant boil early
- Head gasket failure, which can push combustion gas into the coolant
The engine’s oil also helps carry heat. See how engine lubrication works for how the two systems overlap.
Signs of cooling system trouble
- The temperature gauge reading higher than usual, or a warning light
- Steam from under the bonnet
- A sweet smell, often from leaking coolant
- Puddles of coloured fluid under the front of the car
- The coolant level dropping between checks
- The heater blowing cold when the engine should be warm
- White exhaust smoke with a sweet smell, or bubbles in the expansion tank, which can point to a head gasket problem
What to do if your engine overheats
- Ease off. If the gauge starts climbing, reduce load. Switching the heater to hot with the fan on full can draw some extra heat out of the engine in the short term.
- Pull over safely as soon as you can, and switch the engine off if the temperature is in the red or the warning light is on.
- Don’t open the cap while it’s hot. Let the engine cool fully, which may take a good while.
- Check the coolant level once cool, and look for obvious leaks or a broken belt.
- Get it checked before driving far. Continuing to drive an overheating engine can warp the cylinder head or ruin the head gasket.
Looking after the cooling system
- Check the coolant level regularly with the engine cold.
- Replace coolant at the interval in the service schedule. Its corrosion inhibitors wear out over time.
- Use the coolant type and mix the manufacturer specifies.
- Have hoses, the drive belt and the radiator cap inspected as the car ages.
- Keep the front of the radiator clear of leaves and debris.
For how cooling fits with the other systems that keep an engine alive, see how a car engine works.