How a Carburetor Works in One Paragraph
A carburetor mixes fuel into the air an engine draws in, using nothing but air pressure differences and carefully sized passages. As the pistons pull air through the carburetor, the air speeds up through a narrow section called the venturi, and its pressure drops. Fuel stored in a float bowl at near-atmospheric pressure is pushed by that pressure difference through a calibrated jet and out into the fast-moving airstream, where it breaks into fine droplets. The more air flows, the bigger the pressure drop and the more fuel is drawn in, so the mixture stays roughly in proportion. A throttle plate controls how much air (and therefore mixture) reaches the engine. Extra circuits, including the choke, idle circuit, accelerator pump and power valve, fine-tune the mixture for conditions the basic venturi can’t handle on its own.
The Venturi: Where Fuel Meets Air
The heart of a carburetor is the venturi: a section of the carburetor’s throat (or barrel) that narrows and then widens again.
When air flows through the narrow section, it has to speed up to get the same amount of air through a smaller space. According to Bernoulli’s principle, as a fluid’s speed increases, its pressure drops. So the air in the venturi is at lower pressure than the air in the float bowl, which is vented to the atmosphere.
A small nozzle called the discharge nozzle (or main nozzle) opens into the venturi at its narrowest point. The higher pressure on the fuel in the bowl pushes fuel up through the main jet and out of the nozzle into the low-pressure airstream. The fast-moving air shears the fuel into droplets and carries it toward the engine.
An important point: when you press the accelerator on most carburetors, you’re not directly adding fuel. You’re opening the throttle to let more air through. More airflow creates a stronger pressure drop in the venturi, which draws more fuel. (The accelerator pump, covered below, is the main exception.)
The Float Bowl, Float and Needle Valve
The carburetor needs a steady supply of fuel at a consistent level, so it has its own small reservoir: the float bowl (or float chamber).
- Fuel arrives from the tank, either by gravity or from a fuel pump.
- A float sits on the fuel’s surface inside the bowl.
- The float is linked to a needle valve (needle and seat) at the fuel inlet.
- As the fuel level rises, the float rises and pushes the needle into its seat, shutting off the flow.
- As the engine uses fuel and the level drops, the float drops and the needle opens to let more in.
This keeps the fuel at a set height relative to the jets. The level matters. If it’s too high, the engine runs rich or the carburetor floods. If it’s too low, the engine can run lean or starve for fuel under hard use. Float height is usually set to a specification during a rebuild.
The bowl is vented so that the fuel sits at near-atmospheric pressure. That vent is what lets the pressure difference across the venturi do its job.
Jets, Emulsion Tubes and Air Bleeds
Jets are small precision-drilled brass fittings that limit how much fuel can flow through a circuit. A larger jet lets more fuel through, making the mixture richer. A smaller jet makes it leaner. Changing jets (“re-jetting”) is the classic way to tune a carburetor for a different engine setup, exhaust or altitude.
The basic venturi alone doesn’t keep the air-fuel ratio constant. It tends to run richer as airflow increases. To correct this, many carburetors mix a small amount of air into the fuel before it reaches the nozzle, through air bleeds and emulsion tubes. This pre-mixed “emulsion” also atomises more easily. The result is a mixture that stays closer to the target across a wider range of airflow. Our air-fuel ratio guide explains what that target is.
The Throttle Plate
Downstream of the venturi sits the throttle plate, a flat disc on a spindle (often called a butterfly valve). In a car it’s linked to the accelerator pedal. On a motorcycle it’s linked to the twist grip, and on small engines to a governor or lever.
- Closed (or nearly closed): very little air passes, creating strong vacuum below the plate. The engine idles.
- Open: more air flows through the venturi, more fuel is drawn in and the engine makes more power.
How the Carburetor Handles Different Conditions
The venturi and main jet work well at steady, moderate-to-high airflow. Other situations need help, so carburetors have several circuits, each handling a particular job.
Cold Start: The Choke
Cold fuel doesn’t vaporise well and tends to condense on cold intake surfaces, so a cold engine needs a much richer mixture to start and run.
The choke is a second plate above the venturi. When it’s closed or partly closed, it restricts the incoming air. That increases the vacuum inside the carburetor, drawing extra fuel and enriching the mixture.
- Manual chokes are operated by a knob or lever.
- Automatic chokes use a temperature-sensitive bimetallic spring, often with an electric heater or exhaust heat, to open the choke gradually as the engine warms.
Many cars with automatic chokes also have a fast idle cam, which holds the throttle slightly open while the choke is on, so the cold engine idles faster and more steadily. If the choke stays closed after the engine warms up, the engine runs rich, wastes fuel and may run roughly or foul its spark plugs.
Idle and Off-Idle Circuits
At idle, the throttle is almost closed and so little air flows through the venturi that the main circuit can’t draw fuel. The idle circuit takes over. It feeds fuel through a small idle jet to a port just below the throttle plate, where the strong vacuum draws it in. An adjustable idle mixture screw sets how much fuel this circuit delivers.
As the throttle starts to open, there’s a brief gap before the main circuit begins working. Off-idle or transition ports, small holes just above the closed throttle plate, are uncovered as it opens and supply extra fuel to smooth the handover.
Cruise: The Main Circuit
At steady part throttle and above, airflow through the venturi is strong enough for the main metering circuit, made up of the main jet, emulsion system and discharge nozzle, to supply most of the fuel. This is where the engine spends most of its time on the road.
Sudden Throttle: The Accelerator Pump
When the throttle snaps open, air rushes in instantly but fuel, being much heavier, lags behind. Without help, the mixture goes momentarily lean and the engine stumbles or hesitates.
The accelerator pump, a small piston or diaphragm linked to the throttle, squirts a shot of fuel directly into the carburetor throat whenever the throttle opens quickly. This is also why pumping the accelerator before starting an old carbureted engine adds fuel for a cold start. Too much pumping can flood it, though.
Full Load: Power Valve or Metering Rods
Under heavy load, the engine needs a richer mixture for maximum power and to help protect against knock. Many carburetors add extra fuel in one of two ways:
- Power valve: a spring-loaded valve held closed by engine vacuum. When vacuum falls under heavy load, it opens and adds fuel to the main circuit.
- Metering rods (step-up rods): tapered rods that sit in the main jets. Under heavy load they lift out, opening up the jets and letting more fuel flow.
Types of Carburetors
Carburetors share the same basic principles but come in several designs:
- Fixed-venturi carburetors: the common type on older cars and many small engines, with a fixed-size venturi. They range from simple single-barrel units to two-barrel and four-barrel designs, where secondary barrels open under heavy load to supply more air and fuel.
- Constant-velocity (CV) or variable-venturi carburetors: a piston or slide rises and falls with engine vacuum, changing the venturi size so air speed stays roughly constant. A tapered needle on the piston varies the fuel flow. SU carburetors on classic British cars and many motorcycle carburetors work this way.
- Diaphragm carburetors: used on chainsaws, string trimmers and other tools that run at any angle. A flexible diaphragm replaces the float, so fuel delivery works in any orientation.
- Updraft, downdraft and sidedraft: these describe the direction air flows through the carburetor. Many older aircraft engines use updraft carburetors, many American cars used downdraft, and sidedraft designs were common on European performance cars.
Carburetor Icing
The pressure drop in the venturi and the evaporation of fuel can cool the air inside a carburetor sharply. In humid conditions, ice can form in the throat and around the throttle plate, even when the outside air is well above freezing. Ice restricts airflow and can cause rough running or power loss.
This is a well-known hazard for carbureted aircraft engines, which use carburetor heat, a valve that routes warm air from around the exhaust into the carburetor, to prevent or clear ice. Pilots should follow their aircraft’s operating handbook and training on when to use it. Cars have historically used intake manifold heating or heated air intakes for a similar purpose.
Common Carburetor Problems
Carburetors are simple, but they have a few typical failure points:
- Varnish and clogged jets from stale fuel. Gasoline that sits for weeks or months can leave gummy deposits that block tiny passages, especially the idle circuit. The classic symptom is an engine that won’t start, or won’t idle, after storage. Running seasonal equipment dry or using fuel stabiliser before storage helps prevent it.
- Sticking float or needle valve. If the needle doesn’t seal, the bowl overfills and the engine floods. You may see fuel dripping from the carburetor or smell raw fuel. If it sticks closed, the engine starves.
- Choke problems. A choke stuck closed causes rich running and black smoke. A choke stuck open makes cold starts difficult.
- Vacuum leaks. Air leaking in past gaskets or cracked hoses below the carburetor leans the mixture, often causing a high or unstable idle.
- Worn throttle shafts and gaskets. These can let in unmetered air and cause similar lean symptoms.
- Incorrect jetting. After engine or exhaust changes, or at a very different altitude, the original jets may no longer suit the engine.
Safety note: raw fuel around a hot engine is a fire hazard. If you smell gasoline or see fuel leaking from a carburetor, stop the engine and fix the leak before running it again.
Why Cars Moved to Fuel Injection
Carburetors are clever, but they meter fuel only approximately and can’t correct themselves based on what’s coming out of the exhaust. Tightening emissions rules and the need for catalytic converters, which work best with a tightly controlled mixture, pushed carmakers toward electronic fuel injection from the 1980s onward.
Our fuel injection guide explains how those systems work, and our comparison of whether fuel injected or carbureted is better covers where carburetors still make sense today.