Small engines power lawnmowers, tillers, generators, pressure washers and snow blowers. They’re mechanically simple, which makes them good candidates for home repair. Most problems come down to a short list of causes, and stale fuel tops that list. This guide walks through a reliable troubleshooting order and the fixes for the most common faults.
What a small engine needs to run
A small gasoline engine needs:
- Fuel mixed with air in the right proportion, usually by a carburetor
- Spark at the right moment, from a magneto ignition coil mounted next to the flywheel
- Air through a reasonably clean filter
- Compression from a cylinder that seals properly
The first three are what people usually mean by “the three things a small engine needs.” Compression is the fourth, and it’s easy to forget. If an engine has all four, it should run. Troubleshooting is simply finding out which one is missing.
Safety before you start
- Disconnect the spark plug wire before working near the blade, flywheel or other moving parts. On a mower, a blade turned by hand can start the engine.
- Work outdoors or in a well-ventilated area, away from open flames, pilot lights and sparks. Gasoline vapor is highly flammable.
- Let the engine cool before handling the muffler, cylinder or fuel.
- Don’t check for spark by holding a plug near the spark plug hole with fuel vapor around. Use an inline spark tester instead.
- Tip mowers carefully and follow the manufacturer’s advice on which side to tip them, so oil and fuel don’t flood the air filter or carburetor.
How to troubleshoot a small engine, step by step
- Check the basics. Is there fuel in the tank? Is the fuel valve open? Is the safety bail or handle held correctly? Is the choke set correctly? On riding equipment, check the seat switch, parking brake and neutral switches.
- Check the fuel. Fuel that has sat for a month or more, especially ethanol-blended fuel, can go stale and leave varnish. If the fuel smells sour or looks darker than fresh gasoline, drain it and refill with fresh fuel.
- Check the air filter. Remove it. A badly clogged filter can choke the engine, and a soaked foam filter can starve it of air.
- Check for spark. Remove the plug, look at its condition, and connect an inline spark tester between the plug and the plug wire. Pull the cord. You should see a clear spark. A wet, black or oily plug, or a cracked insulator, means replace it.
- Check for fuel delivery. If there’s spark but no start, try a very small amount of fresh fuel or starting spray in the carburetor intake, then try to start.
- If it fires briefly and dies, fuel isn’t reaching the engine, which usually points to the carburetor.
- Use starting spray sparingly and never near a hot engine.
- Check compression. A healthy engine gives firm resistance on the pull cord. A pull with little resistance can mean worn rings, a stuck or burned valve, a blown head gasket or incorrect valve clearance. Some engines have compression release mechanisms, so a compression gauge reading isn’t always straightforward. Check the manufacturer’s information.
Common small engine problems and fixes
Engine won’t start
- Stale fuel or a gummed carburetor are the most common causes. Clean or rebuild the carburetor, or replace it if it’s badly corroded. See the most common carburetor problems.
- Fouled or worn spark plug: replace it and set the gap to specification.
- Faulty ignition coil: no spark with a good plug and wiring.
- Kill wire or safety switch shorting: a chafed wire that grounds the coil kills the spark. Disconnect the kill wire at the coil as a test only, and remember the engine may then not shut off normally.
- Sheared flywheel key: after a mower blade hits a rock, root or curb, the soft flywheel key can shear, which throws off ignition timing. The engine may kick back, backfire or refuse to start despite good spark. Remove the flywheel and inspect the key.
- Flooding: too much choke or a stuck float. Wait, remove the plug, dry it and try again with the choke off.
Only runs with the choke on
If an engine runs only on choke, it’s getting too little fuel (running lean). The choke richens the mixture enough to keep it going. Common causes:
- A partly clogged main jet or idle passage, usually from varnish
- A leaking carburetor gasket or intake gasket letting in extra air
- A low float level or a sticky float needle
- A blocked fuel tank vent or a restricted fuel line or filter
Cleaning the carburetor passages thoroughly usually fixes it.
Surging or hunting
Engine speed rises and falls on its own. This is usually also a lean condition:
- Partly blocked jets
- Air leaks at the carburetor mounting or intake gasket
- A loose governor linkage
- A sticking governor
Clean the carburetor and check that all mounting bolts are tight. Don’t bend governor springs or linkages to “fix” surging. It can lead to overspeeding, which is dangerous.
Starts, then dies
- Fuel not refilling the bowl: clogged filter, kinked line, blocked tank vent or stuck float
- Running out of a primed charge: the primer gets it going, but the carburetor isn’t delivering fuel
- Overheating: blocked cooling fins under the shroud, or low oil
- Low-oil shutdown: many generators and some other engines have a low-oil sensor that stops the engine
Loses power or bogs under load
- A dirty air filter
- A partly blocked fuel system
- A worn spark plug
- Grass buildup under the mower deck adding load
- A dull blade
- Low compression from wear
Smokes
- Blue or white smoke after tipping: oil got into the cylinder or air filter. It often clears after running briefly. Replace a soaked filter.
- Constant blue smoke: overfilled crankcase, worn rings or a worn valve guide
- Black smoke: running rich because of too much choke, a clogged air filter or a flooding carburetor
Pull cord hard to pull or kicks back
- Blade or attachment binding, or debris under the deck
- A sheared flywheel key (advanced timing causes kickback)
- Hydraulic lock from oil or fuel in the cylinder
- A starter recoil mechanism problem
Tecumseh engine troubleshooting
Tecumseh engines powered huge numbers of mowers, snow blowers and tillers for decades, and many are still in use. They share the general troubleshooting steps above, plus a few model-specific habits.
Tecumseh carburetor quirks
- Main jet in the bowl nut: on many Tecumseh float-type carburetors, the nut holding the fuel bowl on also contains the main jet, with tiny passages drilled through it. If the engine only runs on choke or surges, remove the bowl nut and carefully clear its small holes. Use carburetor cleaner and a fine wire or compressed air, without enlarging them.
- Primer bulbs: cracked or hardened primer bulbs leak air and prevent priming. They’re often replaceable.
- Welch plugs: some Tecumseh carburetors have soft metal plugs covering passages. Thorough cleaning sometimes means removing and replacing these, which takes care.
- Fixed vs. adjustable jets: older models may have adjustable idle and high-speed mixture screws. Many later ones have fixed jets.
How to check a coil on a Tecumseh engine
- Test for spark with an inline spark tester and a known-good plug.
- Disconnect the kill wire at the coil, or check the safety switch circuit, to rule out a wiring short.
- Check the air gap between the coil legs and the flywheel magnets. It should be set to the manufacturer’s specification, which is commonly a small gap of around a hundredth of an inch. Check your engine’s service data. A gap set too wide gives a weak or no spark.
- Inspect the flywheel magnets for rust or debris, and check that the flywheel key is intact.
- If there’s still no spark with correct gap and wiring, the coil is likely faulty. Some technicians measure coil resistance with a multimeter, but specifications vary by model, and a coil can pass a resistance test yet fail under load or when hot.
Are Tecumseh engines junk?
Not inherently. Many Tecumseh engines ran reliably for years, and plenty still do. Tecumseh stopped producing small engines over a decade ago, though. The practical problem is parts availability. Common items like carburetors, coils, gaskets and filters are often still available from aftermarket suppliers, but some model-specific parts are getting harder to find. For a worn-out Tecumseh with major internal damage, repowering with a new engine may make more sense than a rebuild.
Preventing small engine problems
- Use fresh fuel, and buy only what you’ll use within a reasonable time.
- Add a fuel stabilizer if the fuel will sit, or use ethanol-free fuel where it’s available and recommended.
- Run the engine dry or drain the fuel before long storage, as the manufacturer recommends.
- Change the oil at the recommended interval. Small engines often hold very little oil.
- Clean or replace the air filter regularly, more often in dusty conditions.
- Keep the cooling fins clean under the shroud.
- Replace the spark plug periodically.
For the same logic applied to larger engines, see how to diagnose engine problems.