An engine overhaul restores a worn engine to a serviceable condition. The engine is taken apart, every critical part is inspected and measured, worn parts are machined or replaced, and it’s reassembled to specification. Done well, an overhaul can give an engine a long second life. Done carelessly, it can fail quickly. This guide explains what’s involved, how a top-end overhaul differs from a full one, and what drives the time and cost.
What does it mean to overhaul an engine?
“Overhaul” and “rebuild” are often used interchangeably for car engines. Both generally mean disassembling the engine, cleaning and inspecting it, then replacing or reconditioning parts that are worn beyond limits. Related terms:
- Full (major) overhaul: the whole engine, including the bottom end (crankshaft, bearings, pistons, rods) and the top end (cylinder heads and valvetrain)
- Top-end overhaul: cylinder heads, valves and related parts only. Depending on who’s using the term, it may also include pistons and rings.
- In-frame overhaul: common on heavy diesel engines with replaceable cylinder liners. The engine is overhauled without removing it from the vehicle.
- Remanufactured engine: an engine rebuilt in a production setting, usually to a defined standard with all wear parts replaced, and often sold with a warranty
- Short block / long block: a short block is the block with rotating assembly. A long block adds the cylinder heads and valvetrain.
Full overhaul vs. top-end overhaul
A top-end overhaul makes sense when the problems are in the cylinder heads:
- Burned or leaking valves
- Worn valve guides or seals causing oil consumption
- A warped head after overheating
- A head gasket failure
The bottom end must still be in good condition, which a compression and leak-down test can help confirm.
A full overhaul is needed when the bottom end is worn too:
- Worn rings and cylinders, so high oil consumption and blow-by
- Worn bearings, showing as low oil pressure or knocking
- A damaged crankshaft
Our article on worn engine symptoms explains how to tell these apart.
Signs an engine may need an overhaul
- High oil consumption with blue smoke. See why an engine burns oil.
- Low or uneven compression
- Heavy blow-by
- Low oil pressure when hot. See low oil pressure causes.
- Bearing knock. See engine knocking noise.
- Metal debris in the oil. See metal shavings in oil.
- Damage after a major event such as severe overheating, oil starvation or a timing belt failure on an interference engine
The full engine overhaul procedure
The outline below is general. Every engine has its own specifications, sequences and torque values. Always work from the factory service manual or equivalent data.
1. Diagnose and plan
Confirm the engine actually needs an overhaul, and find out why it wore out or failed. An engine that failed from overheating or oil starvation will fail again if the root cause isn’t fixed. Gather the service manual, gasket sets, bearings, rings and other parts. Line up a machine shop before you start.
2. Remove the engine
Drain the fluids. Disconnect wiring, hoses, the exhaust and accessories. Lift the engine out with a suitable hoist, either alone or together with the transmission depending on the vehicle. Mount it on an engine stand. Photograph connections and routing before disconnecting anything.
3. Disassemble and label
Remove the intake and exhaust manifolds, valve covers, timing components, cylinder heads, oil pan and oil pump. Then remove the pistons and connecting rods, and finally the crankshaft.
Keep parts in order and labeled by cylinder and position, especially lifters, rockers, pushrods, bearing caps and valves. Many of these parts wear into each other, and bearing caps are machined with the block and must go back in their original places and orientation.
4. Clean
Clean every part thoroughly to remove oil, sludge, carbon and old gasket material. Machine shops often hot-tank or bake blocks and heads, though not all methods are suitable for aluminum. Oil passages and galleries should be cleared, often by removing gallery plugs, so no debris is left to circulate later.
5. Inspect and measure
This is where an overhaul is won or lost. Typical checks include:
- Block: cracks; cylinder bore size, taper and out-of-round; deck flatness; main bearing bore alignment
- Cylinder heads: cracks (often by pressure testing or crack detection), flatness, valve guide wear, seat condition
- Crankshaft: journal size, taper and out-of-round; straightness; surface condition
- Connecting rods: big-end bore size and roundness, straightness
- Camshaft and lifters: lobe wear, journal wear
- Pistons: skirt wear, ring groove wear, pin fit
Measurements are compared with the manufacturer’s limits using micrometers, bore gauges, feeler gauges and straightedges.
6. Machine work
Depending on what the measurements show:
- Bore and hone cylinders oversize (with matching oversize pistons), or just hone to restore the crosshatch if the bores are within limits
- Grind the crankshaft undersize (with matching undersize bearings), or polish the journals
- Resurface the block deck and cylinder heads
- Valve job: grind or replace valves, recut seats, replace guides and seals as needed
- Recondition rods, and align-hone the main bearing bores if required
- Balance the rotating assembly, common in performance builds and sometimes recommended in others
7. Reassemble
Reassembly is careful, clean work:
- Check clearances during assembly: bearing oil clearances (with Plastigage or by measuring), ring end gaps, crankshaft end play and rod side clearance
- Use assembly lubricant on bearings, cam lobes and other parts that will run before oil pressure builds
- Torque fasteners to specification in the correct sequence. Many modern engines use torque-to-yield head and bearing bolts that must be replaced, not reused.
- Set valve timing precisely using the timing marks or locking tools specified
- Install new gaskets and seals throughout. Reusing old soft parts is a common cause of leaks after a rebuild.
8. Install, prime and start
Reinstall the engine and reconnect everything. Fill it with the correct oil and coolant. Prime the oil system before the first start where the procedure calls for it, so the bearings aren’t run dry. On the first start, watch oil pressure, coolant temperature and leaks closely. Bleed air from the cooling system.
9. Break-in
New rings need to seat against the freshly honed cylinders. Follow the ring and engine manufacturer’s break-in advice. That often means varying engine speed and load moderately, avoiding long periods at constant speed or heavy loads early on, and changing the oil and filter after a short initial period. Flat-tappet camshafts often have their own specific break-in procedure and oil requirements.
The engine top overhaul procedure
A top overhaul in a car engine typically includes:
- Removing the intake and exhaust manifolds, valve covers and timing components as needed
- Removing the cylinder heads
- Disassembling, cleaning and crack-checking the heads
- Checking head flatness and resurfacing if needed
- A valve job: valves, seats, guides and valve stem seals
- Inspecting the camshaft(s), followers or lifters, and replacing worn parts
- Cleaning the block deck and checking it for flatness
- Reassembling with new head gaskets, head bolts if specified, and other gaskets
- Setting valve timing and, where adjustable, valve clearances
Because the bottom end isn’t touched, a top overhaul won’t cure worn rings, bearing wear or a damaged crankshaft. A healthy bottom end with new valve seals and a fresh valve job can still run well for a long time, though.
Aircraft engines: top overhaul and TBO
Aviation has its own, more formal terminology.
What a top overhaul includes: for piston aircraft engines, a top overhaul generally means working on the cylinders without opening the crankcase. The cylinders, pistons, rings and valve components are reconditioned or replaced. A major overhaul includes disassembling the whole engine and inspecting and reconditioning it to defined limits.
Hours between overhauls: engine manufacturers publish a recommended time between overhaul (TBO). It varies by engine model and is commonly in the range of roughly 1,200 to 2,400 hours for many piston aircraft engines. Calendar-time recommendations may also apply. Whether TBO is mandatory depends on the type of operation and the applicable regulations.
Can an A&P do an engine overhaul? In the United States, an appropriately certificated mechanic with a powerplant rating can perform engine overhaul work. Rules govern how the work is recorded and approved for return to service, and some major repairs require additional authorization. A “rebuilt,” or zero-time, engine is different: it can come only from the manufacturer or an agency it approves. Requirements are set by the FAA and can change, so check current regulations and guidance, or ask an inspector, for your situation.
How long does an overhaul take?
It varies a great deal. The main factors are:
- Engine design and accessibility. Some engines must come out with the transmission or subframe.
- Machine shop turnaround, often the longest part of the job
- Parts availability
- Whether problems are found that need extra machining or parts
- Experience. A first-time DIY rebuild takes much longer than a shop job.
A professional top-end job on an accessible engine may take a few days, including machine shop time. A full overhaul commonly takes longer, from about a week to several weeks. Ask any shop for an estimated timeline that includes machining.
How much does an engine overhaul cost?
There’s no single figure. Cost depends on:
- Labor hours, which vary by vehicle
- Machine work needed
- Parts quality and quantity
- Engine type: four-cylinder, V6, V8, overhead cam or pushrod, turbocharged, diesel
- Regional labor rates
As a rough guide, a full overhaul of a car engine at a shop often costs several thousand dollars, and complex or high-performance engines can cost much more. A top-end overhaul usually costs less than a full overhaul, but cylinder head machining and timing components can still add up.
Aircraft engine overhauls are a separate and typically much more expensive market. Get written quotes that specify the scope of work.
Overhaul, replace or remanufactured?
| Option | Pros | Cons |
|---|---|---|
| Overhaul your engine | Keeps original, matching engine; you control the quality of parts | Takes time; quality depends on the builder |
| Remanufactured engine | Defined standard; often a warranty; faster | Higher upfront cost for some engines; core return usually required |
| Used engine | Often cheapest | Unknown history and wear; limited warranty |
For a car with other significant problems, the engine may not be the only cost to consider. Our guide on how to diagnose engine problems includes some repair-or-replace considerations.