When the starter spins the engine but it never fires, the battery and starter are at least doing their job. Something else is missing. An engine needs air, fuel, spark, compression and correct timing to run, and a crank no-start means at least one of those isn’t there. This checklist works from the quickest checks to the more involved ones. Stop as soon as you find the culprit.
Cranking vs. starting: what the symptom tells you
- Cranks normally but won’t fire: the most common no-start. Usually fuel, spark, security or sensor related.
- Cranks slowly: usually a weak battery, poor connections or a failing starter. That’s a different problem from the one this checklist covers. Charge or test the battery first.
- Clicks but won’t crank: battery, connections, starter or a safety switch. Also a different problem.
- Starts, then dies right away: often a security immobilizer, a fuel delivery problem or a major vacuum leak.
Before you start: safety and starter care
- Crank in short bursts, commonly no more than about 10 to 15 seconds, with a pause between attempts. Prolonged cranking can overheat the starter and drain the battery.
- If you smell strong fuel or see a leak, stop. Don’t keep cranking or create sparks. Fuel leaks are a fire risk.
- Be careful with starting fluid. It’s highly flammable, and it can cause backfires or engine damage if overused. Don’t use it on diesel engines with glow plugs or intake heaters, where it can ignite violently and damage the engine. Many technicians prefer a spark tester and fuel pressure gauge instead.
- Be ready to stop if the engine was running when it died and now cranks unusually fast. It could have a broken timing belt. On some engines, repeated cranking after a belt failure can cause more damage.
The step-by-step checklist
1. Check the obvious
- Fuel level. Gauges can fail, and a car parked on a slope with a very low tank may not pick up fuel.
- Gear selector in Park or Neutral, and clutch fully pressed on manuals
- Recent events: a fill-up (bad or wrong fuel), a battery disconnect, a repair, or heavy rain or a car wash (wet ignition parts)
2. Watch the security light
Most modern vehicles have an immobilizer that blocks fuel or spark if it doesn’t recognize the key. Look for a flashing key, lock or car-with-key symbol when you try to start. If it’s flashing or stays lit when it normally goes out:
- Try the spare key.
- Replace the key fob battery on push-button start cars. Some vehicles let you start with a dead fob held in a specific spot. Check the owner’s manual.
3. Listen to how it cranks
- Normal rhythm: good compression, as expected. Move on to fuel and spark.
- Unusually fast, light or even cranking, like the engine has no resistance: this can mean no compression, often from a broken or slipped timing belt or chain. Check before cranking further. On some engines you can see the belt through an inspection opening, or watch whether the camshaft turns.
- Uneven cranking with a lump: possible low compression in one cylinder, or a mechanical issue
4. Listen for the fuel pump
On many fuel-injected cars, turning the ignition to on (without cranking) runs the fuel pump for a couple of seconds to build pressure. You may hear a brief hum from the rear of the car.
- No hum at all: check the pump fuse and relay, and the inertia or safety cut-off switch some vehicles have, which can trip after a jolt.
- A hum doesn’t guarantee good pressure, but no hum is a strong clue.
5. Check fuses and relays
Check the fuses for the fuel pump, ignition, engine computer and injectors, in both the engine bay and the interior fuse box. Look at the fuse diagram on the cover or in the manual. A blown fuse often has a reason, such as a shorted wire or a failing component, so if it blows again, find out why.
6. Scan for codes
Even if the check engine light isn’t on, the engine computer may have stored codes. Crankshaft and camshaft position sensor codes, immobilizer codes and fuel pump circuit codes can point straight at the cause. Many auto parts stores will scan for free. Our guide to doing a car diagnostic yourself explains how.
7. Watch the tachometer while cranking
On many vehicles, the tachometer shows a small RPM reading while cranking, often a few hundred RPM. If it doesn’t move at all, the engine computer may not be getting a signal from the crankshaft position sensor. Without that signal, many engines fire neither spark nor injectors. This isn’t true of every vehicle, but it’s a useful clue on many.
8. Test for spark
Use an inline spark tester between a spark plug and its coil or wire, then crank. You should see a consistent spark. On coil-on-plug engines, the service procedure may involve disabling injectors so fuel isn’t sprayed while you test.
- No spark on any cylinder: points to a shared cause, such as the crank sensor, ignition power or ground, an immobilizer, a computer fault or an ignition relay.
- Spark on some cylinders but not others: unlikely to cause a total no-start on its own.
Don’t hold a plug wire near metal by hand, or test spark near fuel vapor. Use the tester.
9. Test for fuel
- Fuel pressure gauge: many fuel-injected engines have a test port on the fuel rail. Compare the reading with the specification for your vehicle. Fuel systems are under pressure, so relieve it as the service procedure describes before opening any connection.
- Noid light: plugs into an injector connector and flashes if the computer is pulsing the injector.
- Smell: a strong fuel smell at the tailpipe after cranking suggests fuel is getting in but not burning, which could be no spark or flooding.
If there’s good spark and the engine fires briefly when a small amount of fuel is introduced, the problem is almost certainly fuel delivery. Our article on carburetor problems covers carbureted engines.
10. Consider flooding
Too much fuel can wet the spark plugs and stop them firing. Flooding is more common after very short drives in cold weather, after repeated failed starts, or with a leaking injector.
- Many fuel-injected cars have a “clear flood” mode: with the accelerator held fully to the floor while cranking, the computer cuts or reduces fuel. Check your owner’s manual.
- If flooding persists, remove the plugs to check whether they’re wet and fuel-fouled.
11. Check compression and timing
If spark and fuel are both present and the engine still won’t start, check the mechanical side:
- Timing belt or chain: inspect the belt if accessible, or confirm that the camshaft turns when cranking
- Compression test: all cylinders low points to timing, or in rare cases severe wear or major damage. See worn engine symptoms for interpreting results.
Quick reference: likely causes by clue
| What you notice | Likely causes |
|---|---|
| Security light flashing | Immobilizer not recognizing the key or fob |
| No fuel pump hum | Pump fuse or relay, inertia switch, failed pump, wiring |
| Tachometer doesn’t move while cranking | Crankshaft position sensor or its circuit (on many vehicles) |
| No spark on any cylinder | Crank sensor, ignition relay or fuse, immobilizer, computer power or ground |
| Strong fuel smell, wet plugs | Flooding, leaking injector, no spark |
| Fires briefly with added fuel, then dies | Fuel delivery problem |
| Cranks fast and even, no resistance | Broken timing belt or chain, no compression |
| Started fine before a car wash or rain | Moisture in ignition components |
| Problem began right after a fill-up | Contaminated or wrong fuel |
Diesel engines that crank but won’t start
Diesels don’t use spark plugs. They rely on heat from compression, so the checklist changes:
- Glow plugs or intake heater: critical in cold weather. Wait for the glow plug light to go out before cranking.
- Air in the fuel system: common after running out of fuel or changing a filter. Many diesels need priming or bleeding.
- Fuel gelling in very cold weather if the fuel isn’t winter-grade
- Water in the fuel: many diesels have a water separator that should be drained regularly
- Low cranking speed: diesels need good cranking speed to reach ignition temperature, so battery condition matters a lot
When to call for help
Call a professional or arrange a tow if:
- You smell fuel or see a leak
- You suspect a broken timing belt
- The immobilizer won’t accept any key
- Spark and fuel tests point to a computer or sensor fault you can’t confirm
- You’ve worked through the checklist without finding the cause
The broader method in how to diagnose engine problems can help you organize what you’ve found before you talk to a mechanic.