The short answer
You shouldn’t let a diesel idle for long periods because a diesel at idle runs too cool to burn its fuel cleanly. With almost no load, the engine injects only a tiny amount of fuel into a lot of air, and cylinder and exhaust temperatures stay low. That leads to unburned fuel, soot and carbon build-up, fuel diluting the engine oil, and exhaust that isn’t hot enough for the particulate filter to clean itself. Idling also burns fuel and adds engine hours without moving anywhere.
A few minutes of idling won’t hurt a healthy engine, and there are times when idling is sensible. The problems come from extended, regular idling, such as leaving a truck running for an hour at a job site, every day.
What happens inside a diesel at idle
A diesel controls power by fuel quantity, not by throttling air (see how diesel engines work). At idle the mixture is extremely lean and each combustion event releases little heat. That’s efficient in a sense, but it means the engine never gets properly hot.
Low cylinder temperatures and incomplete combustion
Diesel fuel needs heat to vaporise and burn completely. In a cool cylinder, some fuel doesn’t burn fully. It leaves as unburned hydrocarbons, forms soot, or lands on the cylinder walls. Over time this shows up as carbon deposits on injector tips, valves, piston rings and in the intake.
Wet stacking and carbon build-up
Wet stacking is the term for unburned fuel and soot collecting in the exhaust system. It’s especially well known in generators and other diesels that run for long periods at light load. Signs include a black, oily residue at the exhaust outlet and dripping from exhaust joints. Wet stacking can foul the turbocharger and exhaust components and reduce power.
On engines with EGR, sooty exhaust is fed back into the intake, where it mixes with oily crankcase vapour and forms sludge that sticks EGR valves and narrows intake passages.
Fuel dilution of the oil
Fuel that isn’t burned can slip past the piston rings into the crankcase. This thins the oil and reduces its ability to protect bearings and other parts. Low temperatures also mean moisture and fuel don’t boil off from the oil as they would on a longer, harder drive.
Cylinder glazing
Long periods of idle and light load are often blamed for cylinder glazing, where the fine crosshatch pattern on the cylinder walls gets polished smooth and coated with hard deposits. Glazed bores hold less oil, the rings seal less well, and the engine can start using oil and producing more blow-by.
Idling and modern emissions systems
Modern diesels are particularly sensitive to idling because of their exhaust aftertreatment:
- Diesel particulate filter (DPF): the filter cleans itself by burning off soot, which needs high exhaust temperatures. Idle exhaust is far too cool, so soot accumulates faster than it can be burned. That brings on more frequent active regenerations, warning lights or the need for a parked or forced regen. See how DPF regeneration works.
- EGR: more soot in the exhaust means more soot recirculated into the intake.
- SCR and DEF: the SCR catalyst needs heat to work well, and DEF dosing is restricted when the exhaust is cold. Deposits can form in the exhaust if conditions stay cold for long periods.
Some engines will raise idle speed automatically, or close an exhaust or intake throttle, to keep the aftertreatment warm. That’s a sign of how much the engine dislikes cold idling.
Fuel and engine hours
Idling isn’t free. A heavy-duty truck engine commonly burns somewhere around half a gallon to a gallon of fuel per hour at idle, depending on the engine, idle speed and accessory load. Smaller pickup and car diesels use less, but the fuel is still being spent without covering any distance.
Idling also adds engine hours. Many fleets and manufacturers track hours as well as miles, and some maintenance intervals and warranties are based on hours. A rule of thumb often repeated in the trucking industry equates an hour of idling to somewhere around 25 to 33 miles of driving in terms of engine wear, though that’s a rough estimate rather than a precise figure.
When idling is reasonable
Not all idling is a problem. Short, purposeful idling is normal.
Cold starts
Modern road diesels generally don’t need long warm-up idles. In most conditions, the best approach is to let the engine settle for a short time, then drive gently until it reaches operating temperature, which warms it faster than idling would. In extreme cold, manufacturers may recommend a longer warm-up, a block heater, or a high-idle feature; follow your owner’s manual. See how diesel engines start for cold-weather advice.
Turbo cool-down
After hard work, such as towing up a long grade, a short idle of a minute or two before shutdown lets the turbocharger and exhaust temperatures come down so oil doesn’t cook in the turbo’s bearings. Many modern engines need less of this than older ones, and some engine computers manage it automatically. A gentle final few minutes of driving often achieves the same result.
Work and PTO idling, high-idle modes
Equipment that drives hydraulic pumps or other machinery through a power take-off (PTO) runs under load, which is different from true no-load idling. Some trucks and machines also have a high-idle setting that raises engine speed during long stationary periods, which keeps temperatures up and reduces wet stacking.
Laws on idling
Many places restrict unnecessary idling. In the US, a number of states and cities limit how long vehicles, especially heavy trucks, can idle, often to just a few minutes, with exceptions for things like traffic, maintenance and extreme weather. In England, idling unnecessarily on public roads is an offence under the Road Traffic (Vehicle Emissions) (Fixed Penalty) regulations, and councils can issue fixed penalty notices to drivers who refuse to switch off. Rules vary a lot, so check local regulations if you operate vehicles.
How to cut idle time
- Switch off when you’ll be stopped for more than a short wait. Modern starters and batteries are designed for frequent starts.
- Use stop-start on cars that have it.
- Use auxiliary power units (APUs) or battery-powered systems for cab heating and cooling on sleeper trucks.
- Fit fuel-operated cab heaters, which use a small fraction of the fuel an idling engine burns.
- Use automatic idle shutdown timers, which many truck engines offer.
- Plug in a block heater instead of idling to warm the engine on cold mornings.
- Plan routes and schedules to avoid long waits with the engine running.
Does short-trip driving cause the same problems?
Largely, yes. A diesel used mostly for very short trips never gets fully warm, so it suffers from many of the same issues: soot build-up, oil dilution, and DPF regenerations that start but don’t finish. If your driving is mostly short hops, a regular longer drive at steady speed helps, and it’s worth weighing this when choosing between a gas and diesel engine. For more on what goes wrong when these problems accumulate, see common diesel engine problems.