The short answer
To start a diesel that has run out of fuel, add several gallons of fresh diesel, prime the fuel system to push out the air, then crank the engine in short bursts. On most modern diesels, priming means turning the key to “on” (without cranking) for around 30 seconds, then off, and repeating several times so the electric lift pump can refill the filter and lines. Older diesels usually have a hand primer pump or bleed screw on the fuel filter housing instead.
Always check your owner’s manual first, because the exact procedure differs between engines, and some vehicles have a specific out-of-fuel restart routine.
First: did you run out of diesel, or put gasoline in?
People often say “ran out of gas” meaning ran out of fuel. This article is about a diesel that ran out of diesel.
If you actually put gasoline in a diesel vehicle, don’t follow these steps and don’t start the engine. Gasoline can seriously damage a diesel fuel system. See what happens if you put gasoline in a diesel engine for what to do instead.
Why a diesel won’t just restart after running dry
A gasoline car that runs out of fuel usually restarts after a refill and a bit of extra cranking. A diesel is fussier, for three reasons:
- Air gets into the fuel system. When the tank runs dry, the pump draws air into the lines, filter and pump. Diesel injection systems need a solid column of fuel to build pressure, and air pockets stop that from happening. See how common rail diesel injection works for why pressure matters so much.
- Fuel lubricates the pumps. Running high-pressure pumps without fuel means running them without lubrication, which can cause wear.
- Sediment can be drawn up. The last fuel in a tank can carry water and debris, which may partly clog the filter.
Step-by-step: restarting a diesel that ran out of fuel
1. Add enough diesel
Add a decent amount of clean diesel. Owner’s manuals and roadside advice commonly suggest at least a couple of gallons, and more if the vehicle is parked on a slope, because the fuel pickup may be at one end of the tank. A few gallons, roughly 2 to 5, is a common recommendation.
Use a proper fuel container and keep it in contact with the vehicle’s filler neck while pouring to reduce static. Don’t smoke, and keep sparks and flames away.
2. Prime the fuel system
How you prime depends on the fuel system:
- Electric lift pump (most modern pickups and cars): turn the key to “on” or “run” without cranking. You may hear the pump run. Leave it for around 30 seconds, then switch off. Repeat several times, often 3 to 6 cycles. Some vehicles have a specific priming sequence in the manual.
- Hand primer pump: many older vehicles, tractors, boats and generators have a plunger or bulb on or near the fuel filter. Pump it until it becomes firm, which shows the filter is full.
- Bleed screw: some filter housings have a bleed screw. Open it slightly, pump the primer until fuel comes out with no bubbles, then close it and wipe up any fuel.
3. Bleed remaining air (older/mechanical systems)
On some older diesels with mechanical injection pumps, air can remain between the pump and injectors. The traditional fix is to loosen the injector line nuts slightly while cranking until fuel appears, then tighten them. Only do this on older mechanical systems where the manual allows it, and never on a common rail engine. Modern high-pressure systems run at pressures that can cause serious injury, and most are designed to self-purge air once the low-pressure side is primed.
4. Crank in short bursts
- If the engine has glow plugs, wait for the glow plug light to go out first.
- Crank for no more than about 10 to 15 seconds at a time.
- Rest the starter between attempts, commonly 30 seconds to a couple of minutes, so it doesn’t overheat.
- If it doesn’t fire after a few attempts, prime the system again before cranking more.
Long continuous cranking can overheat and damage the starter motor and flatten the battery.
5. Let it settle and check for warnings
When it starts, it may run roughly or stumble for a few seconds as the last air works through. Let it idle smoothly for a short time, around 30 seconds to a minute, before driving gently. Check the dashboard for warning lights, and refill properly at the next fuel station.
Safety warnings
- Never loosen high-pressure fuel lines on a common rail engine, and never put your hands near a pressurised fuel leak. High-pressure fuel can penetrate the skin, which is a medical emergency.
- Don’t use starting fluid to force it to start. On engines with glow plugs or intake heaters it can ignite in the intake, and it can cause engine damage. More on this in how diesel engines start.
- Don’t pour gasoline, alcohol or other fuels into the tank to help it start.
- Clean up spilled diesel, especially near hot exhaust parts, and dispose of fuel-soaked rags safely.
- Work safely at the roadside, using hazard lights and, where safe, getting off the road.
If it still won’t start
If priming and cranking haven’t worked, possible causes include:
- Not enough fuel added, especially on a slope.
- A clogged fuel filter from sediment picked up when the tank ran dry.
- A weak battery after repeated cranking, which reduces cranking speed and glow plug performance.
- A failed lift pump, sometimes damaged by running dry.
- Air still trapped in the high-pressure side.
At this point it’s usually best to call roadside assistance or a diesel mechanic, particularly on a modern common rail vehicle. Our article on what can stop a diesel from starting has a fuller checklist.
Can running out of fuel damage a diesel?
Once, briefly, usually not; many diesels are restarted this way without lasting harm. But it does carry risks: some high-pressure pumps rely on fuel for lubrication and cooling, sediment can be drawn into filters, and prolonged cranking can wear the starter. Repeatedly running the tank to empty is a bad habit with any diesel. If the engine runs poorly after a refill, have the fuel system checked; see common diesel engine problems for related faults.
Avoiding it next time
- Refill when the tank reaches about a quarter, especially with a modern common rail engine.
- Don’t rely on the range estimate to the last mile; it can be inaccurate on hills or when towing.
- Keep a small, properly labelled diesel container if you work in remote areas, so there’s no chance of mixing it up with gasoline.
- Change fuel filters on schedule so a little sediment doesn’t become a bigger problem.